Products Catalog

P.Audio

P.Audio C12-400F

The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.7Ω Fs 67 Hz Mms 51.56 g Mmd 44.53 g Qms 7.15 Qes 0.70 Qts 0.64 Vas 43.16 lt SD 530.9 cm2 BI 13.26 Tm Cms 1.1e-04 m/N Rms 3.05 Ns/m Le (at 1kHz) 0.44 mH The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C12-400N

The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.6Ω Fs 66 Hz Mms 53.20 g/1.88 oz Mmd 45.99 g/1.59 oz Qms 6.74 Qes 0.54 Qts 0.50 Vas 43.11 lt/1.52 ft3 SD 530 cm2 BI 15.06 Tm Cms 1.1e-04 m/N Rms 3.42 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C12-500MB

The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 62 Hz Mms 75.80 g/2.67 oz Mmd 68.35 g/2.41 oz Qms 6.66 Qes 0.42 Qts 0.40 Vas 37.95 lt/1.34 ft3 SD 552 cm2 BI 20.03 Tm Cms 8.9e-05 m/N Rms 4.37 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C12-500N

The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 6.8Ω Fs 45.4 Hz Mms 67.11 g Qms 4.690 Qes 0.288 Qts 0.271 Vas 78.87 lt SD 0.551 sqm BI 21.28 Tm Le (at 1kHz) 0.62 mH The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C15-400B

The P.Audio C15-400B is a high performance wide bandwidth transducer. The C15-400B is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C15-400B has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 55Hz to 2000Hz. The C15-400B features a large 3 inch (75.7mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1600 watts of peak rated power handling when sufficient amplifier headroom is available. The C15-400B utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s inside/ outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.4Ω Fs 42 Hz Mms 102.98 g/3.63 oz Mmd 88.60 g/3.13 oz Qms 5.09 Qes 0.61 Qts 0.55 Vas 141.96 lt/5.01 ft3 SD 855 cm2 BI 15.55 Tm Cms 1.4e-04 m/N Rms 5.40 Ns/m Le (at 1kHz) 0.35 mH The P.Audio C15-400B is a high performance wide bandwidth transducer. The C15-400B is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C15-400B has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 55Hz to 2000Hz. The C15-400B features a large 3 inch (75.7mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1600 watts of peak rated power handling when sufficient amplifier headroom is available. The C15-400B utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s inside/ outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C15-400F

The P.Audio C15-400F is a high performance wide bandwidth transducer. The C15-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C15-400F has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 40Hz to 2500Hz. The C15-400F features a large 3 inch (76.32mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1600 watts of peak rated power handling when sufficient amplifier headroom is available. The C15-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s inside/ outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 6.4Ω Fs 45 Hz Mms 78.37 g Mmd 63.99 g Qms 8.32 Qes 0.37 Qts 0.35 Vas 163.61 lt SD 855.3 cm2 BI 19.53 Tm Cms 1.6e-04 m/N Rms 2.68 Ns/m Le (at 1kHz) 0.87 mH The P.Audio C15-400F is a high performance wide bandwidth transducer. The C15-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C15-400F has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 40Hz to 2500Hz. The C15-400F features a large 3 inch (76.32mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1600 watts of peak rated power handling when sufficient amplifier headroom is available. The C15-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s inside/ outside wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C15-600EL

The P.Audio C15-600EL is a high output wide bandwidth transducer. The C15-600EL is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C15-600EL has been optimized for use in two way or three way sound reinforcement systems and has a rated operating range of 55Hz to 2000Hz. The C15-600EL employs a large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 1200 watts of continuous power handling and a full 4800 watts of peak rated power handling when sufficient amplifier headroom is available. The C15-600EL utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The C15-600EL also features a double spider configuration that further enhances system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 51 Hz Mms 126.83 g/4.47 oz Mmd 112.45 g/3.97 oz Qms 7.40 Qes 0.43 Qts 0.41 Vas 80.57 lt/2.85 ft3 SD 855 cm2 BL 22.66 Txm Cms 7.9e-05 m/N Rms 5.39 Ns/m Le (at 1kHz) 0.67 mH

P.Audio

P.Audio C18-1000v1

The C18-1000V1 is a high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub-woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-1000V1 employs a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 1000 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high order high pass filtering be employed if extremely high power levels are expected as low frequencies. The C18-1000V1 utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an "inside/outside" geometry with P.Audio"s square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System Linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 43 Hz Mms 165.37 g Mmd 139.75 g Qms 13 Qes 0.54 Qts 0.52 Vas 182.51 lt. SD 1257 cm2 BI 21.87 Tm Cms 8.3 e-05 m/N Rms 3.46 Ns/m Le (at 1kHz) 1.01 mH The C18-1000V1 is a high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub-woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-1000V1 employs a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 1000 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high order high pass filtering be employed if extremely high power levels are expected as low frequencies. The C18-1000V1 utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an "inside/outside" geometry with P.Audio"s square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System Linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C18-1000v3

P.Audio is a very well-known name in the field of Audio Components all across the world. It is one of the world"s leading manufacturers of professional audio loudspeaker components. P Audio speakers are the best loudspeakers available in the world. A range of 10 different low frequency loudspeaker families are manufactured by P Audio. A series of enclosure designs are produced for optimizing each loudspeaker model. Your search for high-power, well-engineered speakers at an affordable price ends with world"s best loudspeakers "P Audio Speakers". The C18-1000v3 is a high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub-woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-1000v3 employs a very large 4.5 inch (114.4mm) diameter voice coil that provides an AES rated 1600 watts of continuous power handling and a full 6000 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high order high pass filtering be employed if extremely high power levels are expected as low frequencies. The C18-1000v3 utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an "inside/outside" geometry with P.Audio"s square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System Linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. All the above integrated features makes C18-1000v one of the best loudspeakers available in P Audio"s loudspeaker range. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 38 Hz Mms 275.64 g Mmd 250.99 g Qms 13 Qes 0.72 Qts 0.68 Vas 130.50 lt. SD 1225 cm2 BI 23.13 Tm Cms 6.2 e-05 m/N Rms 5.16 Ns/m Le (at 1kHz) 1.01 mH The C18-1000v3 is a high output low frequency transducer. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub-woofer response in both live sound and recorded music venues. The operating range is 30Hz to 200Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-1000v3 employs a very large 4.5 inch (114.4mm) diameter voice coil that provides an AES rated 1600 watts of continuous power handling and a full 6000 watts of peak rated power handling when sufficient amplifier headroom is available. It is recommended that the transducer be loaded into a properly designed vented enclosure and that active high order high pass filtering be employed if extremely high power levels are expected as low frequencies. The C18-1000v3 utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is an "inside/outside" geometry with P.Audio"s square wire technology to improve conversion efficiency and provide a very large cross-sectional area for superior cooling. System Linearity is achieved by employing magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design insures very high displacement and linear response while maintaining excellent control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C18-650EL

The P.Audio C18-650EL is a high output low frequency transducer. The C18-650EL is an upgraded design that features many of P.Audios new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-650EL employs a large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 1200 watts of continuous power handling and a full 4800 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-650EL utilizes P.Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audios rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 46 Hz Mms 179.84 g/6.34 oz Mmd 155.18 g/5.47 oz Qms 5.39 Qes 0.58 Qts 0.52 Vas 144.23 lt/5.09 ft3 SD 1225 cm2 BI 22.76 Tm Cms 6.9e-05 m/N Rms 9.57 Ns/m Le (at 1kHz) 0.63 mH The P.Audio C18-650EL is a high output low frequency transducer. The C18-650EL is an upgraded design that features many of P.Audios new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-650EL employs a large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 1200 watts of continuous power handling and a full 4800 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-650EL utilizes P.Audios Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audios rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C18-700Bv2

The P.Audio C18-700Bv2 is a high output low frequency transducer. The C18-700Bv2 is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-700Bv2 employs a large 4 inch (99.3mm) diameter voice coil that provides an AES rated 800 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-700Bv2 utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 43 Hz Mms 206.35 g Mmd 181.70 g Qms 13.18 Qes 0.42 Qts 0.41 Vas 136.61 lt. SD 1255 cm2 BI 27.06 Tm Cms 6.5 e-05 m/N Rms 4.3 Ns/m Le (at 1kHz) 1.28 mH The P.Audio C18-700Bv2 is a high output low frequency transducer. The C18-700Bv2 is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-700Bv2 employs a large 4 inch (99.3mm) diameter voice coil that provides an AES rated 800 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-700Bv2 utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P.Audio C18-800EL

The P.Audio C18-800EL is a high output low frequency transducer. The C18-800EL is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-800EL employs a large 4 inch (99.3mm) diameter voice coil that provides an AES rated 1200 watts of continuous power handling and a full 4800 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-800EL utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.7Ω Fs 43 Hz Mms 183.90 g Mmd 159.25 g Qms 12.28 Qes 0.40 Qts 0.39 Vas 155.84 lt. SD 1255 cm2 BI 26.46 Tm Cms 7.4 e-05 m/N Rms 4.07 Ns/m Le (at 1kHz) 1.27 mH The P.Audio C18-800EL is a high output low frequency transducer. The C18-800EL is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 18 inch (457mm) diameter piston will produce extremely high sound pressure levels at very low frequencies and is ideal for high level deep bass and sub woofer response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C18-800EL employs a large 4 inch (99.3mm) diameter voice coil that provides an AES rated 1200 watts of continuous power handling and a full 4800 watts of peak rated power handling when sufficient amplifier headroom is available. The transducer is optimized for use in properly tuned vented enclosures and will provide maximal reliability when both a vented enclosure and active high pass filtering are employed. The C18-800EL utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's rectangular wire technology to improve conversion efficiency and provide a large crosssectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The double spider design further enhances system mechanical control and reliability. The cone has been treated with a conformal coating designed to provide additional mechanical damping and moisture resistance. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.