Products Catalog

P.Audio

P.Audio 15BM-500B

The P.Audio 15BM-500B is a high output wide bandwidth transducer. The 15BM-500B is a highly upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 15BM-500B has been optimized for use in two way or three way sound reinforcement systems. The 15BM-500B employs a medium format 3.25 inch (82.5mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The 15BM-500B utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s circular wire technology in an inside/outside geometry to insure very high conversion efficiency. The P.Audio circular wire technology and inside/outside winding configuration provides a very large cross-sectional area that substantially improves system cooling and reduces power compression. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 15BM-500B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 41 Hz Mms 90 g/3.17 oz Mmd 74.95 g/2.64 oz Qms 4.21 Qes 0.41 Qts 0.37 Vas 183.44 lt/6.48 ft3 SD 881 cm2 BI 17.76 Tm Cms 1.7e-04 m/N Rms 5.51 Ns/m Le (at 1kHz) 0.43 mH The P.Audio 15BM-500B is a high output wide bandwidth transducer. The 15BM-500B is a highly upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 15BM-500B has been optimized for use in two way or three way sound reinforcement systems. The 15BM-500B employs a medium format 3.25 inch (82.5mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The 15BM-500B utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s circular wire technology in an inside/outside geometry to insure very high conversion efficiency. The P.Audio circular wire technology and inside/outside winding configuration provides a very large cross-sectional area that substantially improves system cooling and reduces power compression. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 15BM-500B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio

P Audio 15BM-600B

Nominal Diameter: 15 inches Rated Impedance: 8 ohms Power Handling Capacity: 600W (AES) Operating Bandwidth (+/-10dB): 40-3000 Hz Sensitivity @ 1W 1M: 96 dB Magnet Type: Ferrite Voice Coil Diameter: 3.2 inches

P.Audio

P.Audio 2Line-6

The P.Audio 2LINE-6 is an six element vertical column array. The 2LINE-6 exhibits progressive directivity control and is an excellent choice for use in reverberant spaces where very controlled and defined vertical radiation is required. The enclosure is a passive design that features high power handling and reliability. The vertical column array consists of six high output, high excursion two inch (51mm) closely spaced dynamic transducers. The close physical spacing insures controlled polar lobing and tight pattern control. The acoustic performance of the 2LINE-6 make it an ideal choice for houses of worship, theaters, commercial venues, airports, and gathering spaces of all sizes. The P.Audio 2LINE-6 is available in both black and white finishes, and is a heavy duty steel enclosure, with steel grill. The cabinet is both zinc plated and powder coated to ensure durability. The input is 2 x Neutrik speakon connectors to allow easy daisy chaining of cabinets. The 2LINE-6 features a rear mounted switch for changing system impedance between 4 and 16 ohms. The 4 ohm setting is intended for use when maximum amplifier power is to be delivered to a single cabinet, or for when the 2LINE-6 is used with the accompanying 2LINE-Sub. The 16 ohm setting allows 4 cabinets to be parallel linked, when a 4 ohm stable amplifier is used. The 16 ohm setting can be used with the accompanying 2LINE-Sub for lower power situations. The 2LINE-Sub high performance subwoofer is optimised for accurate mid-low reproduction, allowing more headroom for the 2LINE-6 column loudspeaker. Without the subwoofer, it is highly recommended that a high pass filter is set at 200Hz (24dB/oct) to ensure no damage to the 2LINE-6 loudspeaker. P.Audio offers a variety of rigging accessories for use within the 2LINE system. When used with the accompanying subwoofer, the 2L-Pole and 2L-PSA allow the 2LINE-6 enclosure to be mounted above the subwoofer at a fixed height. The 2L-PSA features 2 tilt settings either 0 degrees or 10 degrees down tilt to optimise the radiation for the acoustic space. A single or two column array may be mounted using the 2L-PT and 2L-LB brackets. The 2L-PT allows solid wall mounting with up to 60 degrees pan capability and up to 15 degrees down-tilt capability. The 2L-LB can then be used to join two enclosures together, with inter-cabinet tilt capability up to 15 degrees. The P.Audio 2LINE-6 is an six element vertical column array. The 2LINE-6 exhibits progressive directivity control and is an excellent choice for use in reverberant spaces where very controlled and defined vertical radiation is required. The enclosure is a passive design that features high power handling and reliability. The vertical column array consists of six high output, high excursion two inch (51mm) closely spaced dynamic transducers. The close physical spacing insures controlled polar lobing and tight pattern control. The acoustic performance of the 2LINE-6 make it an ideal choice for houses of worship, theaters, commercial venues, airports, and gathering spaces of all sizes. The P.Audio 2LINE-6 is available in both black and white finishes, and is a heavy duty steel enclosure, with steel grill. The cabinet is both zinc plated and powder coated to ensure durability. The input is 2 x Neutrik speakon connectors to allow easy daisy chaining of cabinets. The 2LINE-6 features a rear mounted switch for changing system impedance between 4 and 16 ohms. The 4 ohm setting is intended for use when maximum amplifier power is to be delivered to a single cabinet, or for when the 2LINE-6 is used with the accompanying 2LINE-Sub. The 16 ohm setting allows 4 cabinets to be parallel linked, when a 4 ohm stable amplifier is used. The 16 ohm setting can be used with the accompanying 2LINE-Sub for lower power situations. The 2LINE-Sub high performance subwoofer is optimised for accurate mid-low reproduction, allowing more headroom for the 2LINE-6 column loudspeaker. Without the subwoofer, it is highly recommended that a high pass filter is set at 200Hz (24dB/oct) to ensure no damage to the 2LINE-6 loudspeaker. P.Audio offers a variety of rigging accessories for use within the 2LINE system. When used with the accompanying subwoofer, the 2L-Pole and 2L-PSA allow the 2LINE-6 enclosure to be mounted above the subwoofer at a fixed height. The 2L-PSA features 2 tilt settings either 0 degrees or 10 degrees down tilt to optimise the radiation for the acoustic space. A single or two column array may be mounted using the 2L-PT and 2L-LB brackets. The 2L-PT allows solid wall mounting with up to 60 degrees pan capability and up to 15 degrees down-tilt capability. The 2L-LB can then be used to join two enclosures together, with inter-cabinet tilt capability up to 15 degrees.

P.Audio

P.Audio 2Line-Sub

The P.Audio 2LINE-Sub is an actively driven 10 wooden subwoofer enclosure. The 2LINE-Sub is ideal for use in both portable and fixed installation environments where low frequency extension is desired. The amplifier is a class D design, with universal Switch Mode Power Supply (SMPS). The amplifier output is 300w to drive the 10 transducer component. The amplifier also has a 300w (4 ohm) output available to drive the 2LINE-6 column loudspeaker or other loudspeaker of choice. The 8 switchable EQ presets found on the amplifier panel of the 2LINE-Sub allow different voicing modes with the 2LINE-6, including 1 preset optimised for use with spoken word. For ease of use, the XLR input on the 2LINE-Sub has switchable sensitivity to allow either line level signals or a microphone to be plugged straight into the system. A THRU XLR output is also present, to allow easy system scalability. The cabinet construction is of a heavy duty wood, with thick splatter coat of paint for ultimate durability and easy touch up of cosmetics. The transducer component is a ferrite 10woofer with highly linear suspension design to ensure low distortion and high excursion capabilities. Two recessed handles on the side of the cabinet allow easy portability. The highly rigid steel grill ensures the transducer is protected at all times. 4 Rubber feet on the bottom of the enclosure ensure the sub will not move, and the M20 thread speaker pole mount on the top of the enclosure allows easy system set up when used with the 2L-Pole and 2L-PSA accessories, in order to create a well-balanced 2LINE System. The P.Audio 2LINE-Sub is an actively driven 10 wooden subwoofer enclosure. The 2LINE-Sub is ideal for use in both portable and fixed installation environments where low frequency extension is desired. The amplifier is a class D design, with universal Switch Mode Power Supply (SMPS). The amplifier output is 300w to drive the 10 transducer component. The amplifier also has a 300w (4 ohm) output available to drive the 2LINE-6 column loudspeaker or other loudspeaker of choice. The 8 switchable EQ presets found on the amplifier panel of the 2LINE-Sub allow different voicing modes with the 2LINE-6, including 1 preset optimised for use with spoken word. For ease of use, the XLR input on the 2LINE-Sub has switchable sensitivity to allow either line level signals or a microphone to be plugged straight into the system. A THRU XLR output is also present, to allow easy system scalability. The cabinet construction is of a heavy duty wood, with thick splatter coat of paint for ultimate durability and easy touch up of cosmetics. The transducer component is a ferrite 10woofer with highly linear suspension design to ensure low distortion and high excursion capabilities. Two recessed handles on the side of the cabinet allow easy portability. The highly rigid steel grill ensures the transducer is protected at all times. 4 Rubber feet on the bottom of the enclosure ensure the sub will not move, and the M20 thread speaker pole mount on the top of the enclosure allows easy system set up when used with the 2L-Pole and 2L-PSA accessories, in order to create a well-balanced 2LINE System.

P.Audio

P.Audio A-100FNT

The P.Audio A-100FNT is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The A-100FNT features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The A-100FNT is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The A-100FNT offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers. The P.Audio A-100FNT is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The A-100FNT features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The A-100FNT is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The A-100FNT offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers.

P.Audio

P.Audio BM-D442

BM-D442 The P Audio BM-D442 is a 1.75 inch (44.4mm) medium format diaphragm compression driver coupled to a high density magnetic circuit. The compression driver exit diameter is an industry standard 1 inch (25.4mm). The design of the 442 is based on the extremely successful BM-D440 technology and represents substantial technological advances in both sound quality and ease of integration into system designs. The BM-D442 combines high magnetic field strength and a very lightweight diaphragm assembly, producing in a very high output device that also features extended bandwidth and well defined frequency response. The phase plug is a circumferential slot design that has been redesigned to provide both extended bandwidth and superior response linearity. The phase plug to diaphragm spacing has been optimized for both extended frequency response and increased acoustic damping. The BM-D442 is optimized for very high performance two way system designs and is an excellent high frequency device for professional two way systems. BM-D442 The P Audio BM-D442 is a 1.75 inch (44.4mm) medium format diaphragm compression driver coupled to a high density magnetic circuit. The compression driver exit diameter is an industry standard 1 inch (25.4mm). The design of the 442 is based on the extremely successful BM-D440 technology and represents substantial technological advances in both sound quality and ease of integration into system designs. The BM-D442 combines high magnetic field strength and a very lightweight diaphragm assembly, producing in a very high output device that also features extended bandwidth and well defined frequency response. The phase plug is a circumferential slot design that has been redesigned to provide both extended bandwidth and superior response linearity. The phase plug to diaphragm spacing has been optimized for both extended frequency response and increased acoustic damping. The BM-D442 is optimized for very high performance two way system designs and is an excellent high frequency device for professional two way systems.

P.Audio

P.Audio BM-D460 / BM-D460S

The P.Audio has redefined its BM series of compression drivers. The BMD460S is a state of the art high output compression driver. New developments P.Audio Research and Development have produced new levels of performance. State of the art manufacturing methods insure extremely reliable and consistent designs. The new BM-D460S driver utilizes the recently developed CRT™ technology to substantially improve both the time domain response and reduce distortion through the critical upper vocal range (1.5kHz to 5kHz). This new technology, called Cavity Resonance Technology ™ (CRT) acts to acoustically minimize the cavity found under all suspension driver suspension elements. By employing CRT technology, P.Audio engineers have been able to greatly improve the vocal accuracy in the frequency range where vocal intelligibility is located. Magnetic fluid has also been added to increase thermal transfer and mechanical damping. These changes to the diaphragm and magnet structure assembly have also increased the sound pressure levels and smoothed the response between 10kHz and 20kHz. The result is a more accurate system, particularly for vocal range program material. The BM-D460S is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry, high temperature aluminum to insure extended high frequency response. This diaphragm geometry is ideally suited for foreground/background high performance pa systems. The 1.0 inch (25.4mm) throat exit makes the 460S an excellent choice for extended bandwidth and ultra high frequency applications such as three way designs. The BM-D460S is ideally suited for line array applications or other applications where a mid bass horn or direct radiator driver is also used. This medium format throat and medium format diaphragm insures wide dispersion at very high frequencies and is an excellent choice for three way systems or medium power two way designs. The 1.0 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.0 inch screw/thread on horns. The Ferrite based permanent magnetic system produces a very high efficiency and value. This makes the BM-D460S ideal for professional applications as well as fixed installation systems. The large format Ferrite permanent magnet produces a very high conversion efficiency. The P.Audio has redefined its BM series of compression drivers. The BMD460S is a state of the art high output compression driver. New developments P.Audio Research and Development have produced new levels of performance. State of the art manufacturing methods insure extremely reliable and consistent designs. The new BM-D460S driver utilizes the recently developed CRT™ technology to substantially improve both the time domain response and reduce distortion through the critical upper vocal range (1.5kHz to 5kHz). This new technology, called Cavity Resonance Technology ™ (CRT) acts to acoustically minimize the cavity found under all suspension driver suspension elements. By employing CRT technology, P.Audio engineers have been able to greatly improve the vocal accuracy in the frequency range where vocal intelligibility is located. Magnetic fluid has also been added to increase thermal transfer and mechanical damping. These changes to the diaphragm and magnet structure assembly have also increased the sound pressure levels and smoothed the response between 10kHz and 20kHz. The result is a more accurate system, particularly for vocal range program material. The BM-D460S is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry, high temperature aluminum to insure extended high frequency response. This diaphragm geometry is ideally suited for foreground/background high performance pa systems. The 1.0 inch (25.4mm) throat exit makes the 460S an excellent choice for extended bandwidth and ultra high frequency applications such as three way designs. The BM-D460S is ideally suited for line array applications or other applications where a mid bass horn or direct radiator driver is also used. This medium format throat and medium format diaphragm insures wide dispersion at very high frequencies and is an excellent choice for three way systems or medium power two way designs. The 1.0 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.0 inch screw/thread on horns. The Ferrite based permanent magnetic system produces a very high efficiency and value. This makes the BM-D460S ideal for professional applications as well as fixed installation systems. The large format Ferrite permanent magnet produces a very high conversion efficiency.

P.Audio

P.Audio BM-D740

The P.Audio BM-D740 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D740 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 1.4 inch (35.5mm) throat exit makes the 740 an excellent choice for extended bandwidth and high sound pressure level performance.This medium format throat insures low distortion and high intelligibility and is an industry standard for professional audio applications. This throat diameter has become an industry reference when combined low distortion and extended bandwidth are required. The 1.4 inch diameter throat insures wide dispersion at high frequencies. The 1.4 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.4 inch bolt on horns. The Ferrite based permanent magnetic system produces a very high efficiency.This makes the BM-D740 ideal for high level professional touring applications as well as high level fixed installation systems. The large Ferrite permanent magnet produces remarkably high conversion efficiency. The P.Audio BM-D740 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D740 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 1.4 inch (35.5mm) throat exit makes the 740 an excellent choice for extended bandwidth and high sound pressure level performance.This medium format throat insures low distortion and high intelligibility and is an industry standard for professional audio applications. This throat diameter has become an industry reference when combined low distortion and extended bandwidth are required. The 1.4 inch diameter throat insures wide dispersion at high frequencies. The 1.4 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.4 inch bolt on horns. The Ferrite based permanent magnetic system produces a very high efficiency.This makes the BM-D740 ideal for high level professional touring applications as well as high level fixed installation systems. The large Ferrite permanent magnet produces remarkably high conversion efficiency.

P.Audio

P.Audio BM-D750(II)

The P Audio BM-D750(II) is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D750(II) is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 750 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D750(II) ideal for high level professional touring applications as well as high level fixed installation systems. The P Audio BM-D750(II) is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D750(II) is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 750 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D750(II) ideal for high level professional touring applications as well as high level fixed installation systems.

P.Audio

P.Audio BM-D760

The P.Audio BM-D760 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D760 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 760 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P.Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D760 ideal for high level professional touring applications as well as high level fixed installation systems. The P.Audio BM-D760 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D760 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 760 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P.Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D760 ideal for high level professional touring applications as well as high level fixed installation systems.

P.Audio

P.audio BM-D950

The P.Audio BM-D950 is a very high performance ultra large format compression driver. The driver features a large optimized ferrite motor that provides extended high frequency response and bandwidth. The ultra large format 4 inch (101.6mm) titanium diaphragm produces very high sound pressure level performance. The BM-D950 offers superior vocal fundamentals and excellent vocal range intelligibility while also offering extended high frequency response. The increased magnetic volume insures elevated thermal reliability and reduced high frequency power compression as well as extended high frequency content. The BM-D950 offers very high continuous power handling and excellent reliability. The design allows for the driver to be crossed over as low as 800Hz yet still exhibits full specification performance. The rated continuous power handling is 150 watts. The BM-D950 features a finite element optimized ferrite magnet structure that offers excellent magnetic efficiency. The design features an industry standard 2.0 inch (50.8mm) exit diameter that will accommodate most standard bolt on style high frequency horns. Useable frequency range is 800Hz to 18kHz. The amplitude response is very controlled and offers excellent time domain response. The P.Audio BM-D950 is a very high performance ultra large format compression driver. The driver features a large optimized ferrite motor that provides extended high frequency response and bandwidth. The ultra large format 4 inch (101.6mm) titanium diaphragm produces very high sound pressure level performance. The BM-D950 offers superior vocal fundamentals and excellent vocal range intelligibility while also offering extended high frequency response. The increased magnetic volume insures elevated thermal reliability and reduced high frequency power compression as well as extended high frequency content. The BM-D950 offers very high continuous power handling and excellent reliability. The design allows for the driver to be crossed over as low as 800Hz yet still exhibits full specification performance. The rated continuous power handling is 150 watts. The BM-D950 features a finite element optimized ferrite magnet structure that offers excellent magnetic efficiency. The design features an industry standard 2.0 inch (50.8mm) exit diameter that will accommodate most standard bolt on style high frequency horns. Useable frequency range is 800Hz to 18kHz. The amplitude response is very controlled and offers excellent time domain response.

P.Audio

P.Audio BT15-800A

The P.Audio BT15-800A is a highly upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 4000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The BT15-800A employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous program power handling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.4Ω Fs 48 Hz Mms 94.6 g Mmd 79.55 g Qms 9.41 Qes 0.51 Qts 0.48 Vas 128.23 lt SD 881.4 cm2 BL 17.29 T x m Cms 1.1e-04 m/N Rms 3.02 Ns/m Le (at 1kHz) 0.77 mH The P.Audio BT15-800A is a highly upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 15 inch (381mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 4000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The BT15-800A employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous program power handling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.