P.Audio P-12N

G12-400MB

P.Audio 12BM-300B

The P.Audio 12BM-300B is a high output wide bandwidth transducer. The 12BM-300B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-300B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-300B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-300B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-300B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 48 Hz Mms 57.72 g/2.04 oz Mmd 50.27 g/1.77 oz Qms 4.41 Qes 0.33 Qts 0.31 Vas 81.13 lt/2.87 ft3 SD 552 cm2 BI 17.09 Tm Cms 1.9e-04 m/N Rms 3.98 Ns/m Le (at 1kHz) 0.49 mH The P.Audio 12BM-300B is a high output wide bandwidth transducer. The 12BM-300B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-300B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-300B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-300B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-300B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio 12BM-400B

The P.Audio 12BM-400B is a high output wide bandwidth transducer. The 12BM-400B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-400B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-400B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-400B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-400B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 48 Hz Mms 57.72 g/2.04 oz Mmd 50.27 g/1.77 oz Qms 4.41 Qes 0.33 Qts 0.31 Vas 81.13 lt/2.87 ft3 SD 552 cm2 BI 17.09 Tm Cms 1.9e-04 m/N Rms 3.98 Ns/m Le (at 1kHz) 0.49 mH The P.Audio 12BM-400B is a high output wide bandwidth transducer. The 12BM-400B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-400B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-400B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-400B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-400B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-400F

The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.7Ω Fs 67 Hz Mms 51.56 g Mmd 44.53 g Qms 7.15 Qes 0.70 Qts 0.64 Vas 43.16 lt SD 530.9 cm2 BI 13.26 Tm Cms 1.1e-04 m/N Rms 3.05 Ns/m Le (at 1kHz) 0.44 mH The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-400N

The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.6Ω Fs 66 Hz Mms 53.20 g/1.88 oz Mmd 45.99 g/1.59 oz Qms 6.74 Qes 0.54 Qts 0.50 Vas 43.11 lt/1.52 ft3 SD 530 cm2 BI 15.06 Tm Cms 1.1e-04 m/N Rms 3.42 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-500MB

The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 62 Hz Mms 75.80 g/2.67 oz Mmd 68.35 g/2.41 oz Qms 6.66 Qes 0.42 Qts 0.40 Vas 37.95 lt/1.34 ft3 SD 552 cm2 BI 20.03 Tm Cms 8.9e-05 m/N Rms 4.37 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-500N

The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 6.8Ω Fs 45.4 Hz Mms 67.11 g Qms 4.690 Qes 0.288 Qts 0.271 Vas 78.87 lt SD 0.551 sqm BI 21.28 Tm Le (at 1kHz) 0.62 mH The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio E12-200S

The P.Audio E12-200S is a high output low frequency transducer. The E12-200S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at low frequencies and is ideal for high level full range response in both live sound and recorded music venues. The operating bandwidth of the E12-200S is 50Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The E12-200S employs a medium format 2.5 inch (63.7mm) diameter voice coil that provides an AES rated 200 watts of continuous power handling and a full 800 watts of peak rated power handling when sufficient amplifier headroom is available. The E12-200S utilizes P.Audio"s under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 59 Hz Mms 47.4 g/1.67 oz Mmd 40.37 g/1.42 oz Qms 5.83 Qes 0.63 Qts 0.57 Vas 61.97 lt/2.19 ft3 SD 531 cm2 BI 12.66 Tm Cms 1.6e-04 m/N Rms 2.96 Ns/m Le (at 1kHz) 0.427 mH The P.Audio E12-200S is a high output low frequency transducer. The E12-200S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at low frequencies and is ideal for high level full range response in both live sound and recorded music venues. The operating bandwidth of the E12-200S is 50Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The E12-200S employs a medium format 2.5 inch (63.7mm) diameter voice coil that provides an AES rated 200 watts of continuous power handling and a full 800 watts of peak rated power handling when sufficient amplifier headroom is available. The E12-200S utilizes P.Audio"s under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity.

P.Audio GM12-100F

The P. Audio "Golden Master" GM12-100F is the intersection of advanced design and state of the art manufacturing. The GM12-100F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100F is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 56 Hz Re 5.4 Ohm Qms 5.97 Qes 0.38 Qts 0.35 Bl 18.99 Tm Mms 72.15 g / 2.55 oz Mmd 65.11 g / 2.30 oz Vas 44.70 lt / 1.58 cu.ft3 Sd 531 cm2 Le 0.55 mH Cms 1.1e - 04 m/N Rms 4.25 Ns/m The P. Audio "Golden Master" GM12-100F is the intersection of advanced design and state of the art manufacturing. The GM12-100F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100F is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-100N

The P. Audio "Golden Master" GM12-100N is the intersection of advanced design and state of the art manufacturing. The GM12-100N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100N is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 98 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 55 Hz Re 5.4 Ohm Qms 6.02 Qes 0.33 Qts 0.32 Bl 19.65 Tm Mms 70.12 g / 2.48 oz Mmd 63.08 g / 2.23 oz Vas 47.76 lt / 1.69 cu.ft3 Sd 531 cm2 Le 0.59 mH Cms 1.2e - 04 m/N Rms 4.03 Ns/m The P. Audio "Golden Master" GM12-100N is the intersection of advanced design and state of the art manufacturing. The GM12-100N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100N is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 98 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-88F

The P. Audio "Golden Master" GM12-88F is the intersection of advanced design and state of the art manufacturing. The GM12-88F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88F is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations -general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 56 Hz Re 5.7 Ohm Qms 7.36 Qes 0.44 Qts 0.42 Bl 17.75 Tm Mms 69.33 g / 2.45 oz Mmd 62.29 g / 2.20 oz Vas 45.45 lt / 1.60 cu.ft3 Sd 531 cm2 Le 0.58 mH Cms 1.2e - 04 m/N Rms 3.4 Ns/m The P. Audio "Golden Master" GM12-88F is the intersection of advanced design and state of the art manufacturing. The GM12-88F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88F is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations -general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-88N

The P. Audio "Golden Master" GM12-88N is the intersection of advanced design and state of the art manufacturing. The GM12-88N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88N is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 63 Hz Re 5.7 Ohm Qms 3.61 Qes 0.54 Qts 0.47 Bl 17.78 Tm Mms 75.20 g / 2.65 oz Mmd 68.16 g / 2.41 oz Vas 33.5 lt / 1.18 cu.ft3 Sd 531 cm2 Le 0.50 mH Cms 8.5e - 05 m/N Rms 8.3 Ns/m The P. Audio "Golden Master" GM12-88N is the intersection of advanced design and state of the art manufacturing. The GM12-88N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88N is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GST12-500

The P.Audio GST12-500 is a 12 inch (305mm) diameter high performance woofer. The design utilizes a medium format 3 inch 76mm) nominal voice coil diameter with a very light weight aluminum coil configured in an inside/outside wind geometry. This light weight design, coupled with a low moving mass cone offers excellent transient response. The large format ferrite based magnet structure produces very high conversion efficiency. Inside/outside winding geometry assists in coil cooling and improves both transducer power handling and system reliability. The GST12-500 also features a very long air gap height that improves transducer linearity. The GST12-500 offers very smooth and controlled amplitude response to 2000Hz and has a useable high frequency limit of 3000Hz. The GST12-500 is an excellent choice for high output two way system designs and is ideally coupled with P.Audio BM-D series and SD series compression drivers. P.Audio offers a wide range of high frequency horns that can provide short throw or medium throw designs when coupled with the GST12-500 The design features very large diameter impregnated spiders to insure long term linearity. The impregnated spiders and very high system power handling will insure excellent long term performance. The cone is waterproof to improve reliability in high humidity environments. The GST12-500 features an aluminum die cast chassis that includes P.Audios Auto Balanced Cooling design that minimizes coil and magnet structure heating, and further improves system performance. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 56 Hz Mms 58.40 g/2.32 oz Mmd 58.40 g/2.06 oz Qms 8.34 Qes 0.51 Qts 0.48 Vas 52.86 lt/1.87 ft3 SD 552 cm2 BI 15.70 Tm Cms 1.2e-04 m/N Rms 2.78 Ns/m Le (at 1kHz) 0.52 mH The P.Audio GST12-500 is a 12 inch (305mm) diameter high performance woofer. The design utilizes a medium format 3 inch 76mm) nominal voice coil diameter with a very light weight aluminum coil configured in an inside/outside wind geometry. This light weight design, coupled with a low moving mass cone offers excellent transient response. The large format ferrite based magnet structure produces very high conversion efficiency. Inside/outside winding geometry assists in coil cooling and improves both transducer power handling and system reliability. The GST12-500 also features a very long air gap height that improves transducer linearity. The GST12-500 offers very smooth and controlled amplitude response to 2000Hz and has a useable high frequency limit of 3000Hz. The GST12-500 is an excellent choice for high output two way system designs and is ideally coupled with P.Audio BM-D series and SD series compression drivers. P.Audio offers a wide range of high frequency horns that can provide short throw or medium throw designs when coupled with the GST12-500 The design features very large diameter impregnated spiders to insure long term linearity. The impregnated spiders and very high system power handling will insure excellent long term performance. The cone is waterproof to improve reliability in high humidity environments. The GST12-500 features an aluminum die cast chassis that includes P.Audios Auto Balanced Cooling design that minimizes coil and magnet structure heating, and further improves system performance.

P.Audio SN-12MB

The SN-12MB has been designed specifically for both direct radiator and horn loaded mid bass applications. This SN Series II design has been optimized for use in the critical 60Hz to 2000Hz vocal range and is an ideal choice for professional level three way designs. A typical 12 inch design must offer both good bandwidth, down to 60Hz, and good efficiency. The SN-12MB has all of its performance designed into the 125Hz and above range. This means that the efficiency can be optimized for this frequency range. High efficiency means that lower electrical power levels are required, thus improving both system reliability and reducing power compression. The SN-12MB is a 12 inch (314mm) diameter design that employs very high energy product Neodymium magnetics to proved extremely high conversion efficiency. The medium format 3 inch (76.2mm) voice coil design is an edge wound rectangular aluminum design to further maximize efficiency. Because weight is critical for portable systems or flown/suspended designs, the SN-12MB features a die cast aluminum chassis as well as the light weight Neodymium magnet structure. The performance parameters of the SN-12MB are optimized for professional level mid bass designs. If full range designs are specified the SN-12LF should be utilized. P.Audio features state of the art design and manufacturing that insure the SN-12MB will provide very high power handling and reliability in high performance profession applications. SMALL SIGNAL PARAMETERS Fs 62 Hz Re 5.2Ω Le (at 1kHz) 0.33 mH Qms 6.70 Qes 0.44 Qts 0.41 BI 17 Tm Mms 63.36 g Vas 43.64 lt SD 0.055 m2 Eff 2.22% Hag 8 mm Hve 18 mm Xmax 5 mm The SN-12MB has been designed specifically for both direct radiator and horn loaded mid bass applications. This SN Series II design has been optimized for use in the critical 60Hz to 2000Hz vocal range and is an ideal choice for professional level three way designs. A typical 12 inch design must offer both good bandwidth, down to 60Hz, and good efficiency. The SN-12MB has all of its performance designed into the 125Hz and above range. This means that the efficiency can be optimized for this frequency range. High efficiency means that lower electrical power levels are required, thus improving both system reliability and reducing power compression. The SN-12MB is a 12 inch (314mm) diameter design that employs very high energy product Neodymium magnetics to proved extremely high conversion efficiency. The medium format 3 inch (76.2mm) voice coil design is an edge wound rectangular aluminum design to further maximize efficiency. Because weight is critical for portable systems or flown/suspended designs, the SN-12MB features a die cast aluminum chassis as well as the light weight Neodymium magnet structure. The performance parameters of the SN-12MB are optimized for professional level mid bass designs. If full range designs are specified the SN-12LF should be utilized. P.Audio features state of the art design and manufacturing that insure the SN-12MB will provide very high power handling and reliability in high performance profession applications.

P.Audio TC-150N

The P Audio TC-150N is a high output wide range transducer. The TC-150N is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce high sound pressure levels at low frequencies but also exhibits an extended high frequency response that makes the TC-150N a full range device. The operating bandwidth of the TC-100 is 80Hz-14000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The TC-150N employs a medium format 1.79 inch (45.5mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 450 watts of peak rated power handling when sufficient amplifier headroom is available. The TC-150N utilizes P Audio's under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P Audio's precision round wire technology that maximizes system conversion efficiency and cooling. The Suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.89Ω Fs 51 Hz Mms 39.18 g Mmd 31.73 g Qms 14.55 Qes 0.58 Qts 0.56 Vas 104.64 lt SD 551.5 cm2 BI 11.30 Tm Cms 2.5e-04 m/N Rms 0.87 Ns/m Le (at 1kHz) 0.46 mH The P Audio TC-150N is a high output wide range transducer. The TC-150N is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce high sound pressure levels at low frequencies but also exhibits an extended high frequency response that makes the TC-150N a full range device. The operating bandwidth of the TC-100 is 80Hz-14000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The TC-150N employs a medium format 1.79 inch (45.5mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 450 watts of peak rated power handling when sufficient amplifier headroom is available. The TC-150N utilizes P Audio's under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P Audio's precision round wire technology that maximizes system conversion efficiency and cooling. The Suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity.