P.Audio GM18-100N

G12-400MB

P.Audio 12BM-300B

The P.Audio 12BM-300B is a high output wide bandwidth transducer. The 12BM-300B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-300B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-300B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-300B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-300B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 48 Hz Mms 57.72 g/2.04 oz Mmd 50.27 g/1.77 oz Qms 4.41 Qes 0.33 Qts 0.31 Vas 81.13 lt/2.87 ft3 SD 552 cm2 BI 17.09 Tm Cms 1.9e-04 m/N Rms 3.98 Ns/m Le (at 1kHz) 0.49 mH The P.Audio 12BM-300B is a high output wide bandwidth transducer. The 12BM-300B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-300B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-300B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 300 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-300B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-300B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio 12BM-400B

The P.Audio 12BM-400B is a high output wide bandwidth transducer. The 12BM-400B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-400B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-400B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-400B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-400B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 48 Hz Mms 57.72 g/2.04 oz Mmd 50.27 g/1.77 oz Qms 4.41 Qes 0.33 Qts 0.31 Vas 81.13 lt/2.87 ft3 SD 552 cm2 BI 17.09 Tm Cms 1.9e-04 m/N Rms 3.98 Ns/m Le (at 1kHz) 0.49 mH The P.Audio 12BM-400B is a high output wide bandwidth transducer. The 12BM-400B is an upgraded design that features many of P.Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer has a rated bandwidth of 45Hz to 3000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The 12BM-400B has been optimized for use in two way or three way sound reinforcement systems. The 12BM-400B employs a medium format 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The 12BM-400B utilizes P.Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio's precision circular wire technology to insure high conversion efficiency. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The 12BM-400B also features a single spider configuration that provides system reliability and mechanical control. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-400F

The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.7Ω Fs 67 Hz Mms 51.56 g Mmd 44.53 g Qms 7.15 Qes 0.70 Qts 0.64 Vas 43.16 lt SD 530.9 cm2 BI 13.26 Tm Cms 1.1e-04 m/N Rms 3.05 Ns/m Le (at 1kHz) 0.44 mH The P.Audio C12-400F is a high performance wide bandwidth transducer. The C12-400F is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400F has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 50Hz to 4000Hz. The C12-400F features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-400F utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-400N

The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.6Ω Fs 66 Hz Mms 53.20 g/1.88 oz Mmd 45.99 g/1.59 oz Qms 6.74 Qes 0.54 Qts 0.50 Vas 43.11 lt/1.52 ft3 SD 530 cm2 BI 15.06 Tm Cms 1.1e-04 m/N Rms 3.42 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-400N is a high performance wide bandwidth transducer. The C12-400N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-400N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-400N features a very large 3 inch (76.2mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. TheC12-400N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-500MB

The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 62 Hz Mms 75.80 g/2.67 oz Mmd 68.35 g/2.41 oz Qms 6.66 Qes 0.42 Qts 0.40 Vas 37.95 lt/1.34 ft3 SD 552 cm2 BI 20.03 Tm Cms 8.9e-05 m/N Rms 4.37 Ns/m Le (at 1kHz) 0.31 mH The P.Audio C12-500MB is a high performance wide bandwidth transducer. The C12-500MB is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500MB has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 60Hz to 3000Hz. The C12-500MB features a very large 3.9 inch (99.3mm) diameter voice coil that provides an AES rated 500 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500MB utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio C12-500N

The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 6.8Ω Fs 45.4 Hz Mms 67.11 g Qms 4.690 Qes 0.288 Qts 0.271 Vas 78.87 lt SD 0.551 sqm BI 21.28 Tm Le (at 1kHz) 0.62 mH The P.Audio C12-500N is a high performance wide bandwidth transducer. The C12-500N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels in the mid band and upper mid frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The C12-500N has been optimized for use in two way or three way sound reinforcement systems. The transducer is also ideal as a mid bass driver for ultra high performance system designs and has an operating bandwidth of 45Hz to 3000Hz. The C12-500N features a very large 4 inch (99.3mm) diameter voice coil that provides an AES rated 400 watts of continuous power handling and a full 2000 watts of peak rated power handling when sufficient amplifier headroom is available. The C12-500N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s ribbon rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio E12-200S

The P.Audio E12-200S is a high output low frequency transducer. The E12-200S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at low frequencies and is ideal for high level full range response in both live sound and recorded music venues. The operating bandwidth of the E12-200S is 50Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The E12-200S employs a medium format 2.5 inch (63.7mm) diameter voice coil that provides an AES rated 200 watts of continuous power handling and a full 800 watts of peak rated power handling when sufficient amplifier headroom is available. The E12-200S utilizes P.Audio"s under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 59 Hz Mms 47.4 g/1.67 oz Mmd 40.37 g/1.42 oz Qms 5.83 Qes 0.63 Qts 0.57 Vas 61.97 lt/2.19 ft3 SD 531 cm2 BI 12.66 Tm Cms 1.6e-04 m/N Rms 2.96 Ns/m Le (at 1kHz) 0.427 mH The P.Audio E12-200S is a high output low frequency transducer. The E12-200S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at low frequencies and is ideal for high level full range response in both live sound and recorded music venues. The operating bandwidth of the E12-200S is 50Hz to 3500Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The E12-200S employs a medium format 2.5 inch (63.7mm) diameter voice coil that provides an AES rated 200 watts of continuous power handling and a full 800 watts of peak rated power handling when sufficient amplifier headroom is available. The E12-200S utilizes P.Audio"s under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity.

P.Audio GM12-100F

The P. Audio "Golden Master" GM12-100F is the intersection of advanced design and state of the art manufacturing. The GM12-100F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100F is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 56 Hz Re 5.4 Ohm Qms 5.97 Qes 0.38 Qts 0.35 Bl 18.99 Tm Mms 72.15 g / 2.55 oz Mmd 65.11 g / 2.30 oz Vas 44.70 lt / 1.58 cu.ft3 Sd 531 cm2 Le 0.55 mH Cms 1.1e - 04 m/N Rms 4.25 Ns/m The P. Audio "Golden Master" GM12-100F is the intersection of advanced design and state of the art manufacturing. The GM12-100F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100F is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-100N

The P. Audio "Golden Master" GM12-100N is the intersection of advanced design and state of the art manufacturing. The GM12-100N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100N is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 98 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 55 Hz Re 5.4 Ohm Qms 6.02 Qes 0.33 Qts 0.32 Bl 19.65 Tm Mms 70.12 g / 2.48 oz Mmd 63.08 g / 2.23 oz Vas 47.76 lt / 1.69 cu.ft3 Sd 531 cm2 Le 0.59 mH Cms 1.2e - 04 m/N Rms 4.03 Ns/m The P. Audio "Golden Master" GM12-100N is the intersection of advanced design and state of the art manufacturing. The GM12-100N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 4 inch (101.6mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature copper clad aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-100N is rated at 3200 W peak power handling/ 800 W AES continuous power handling with nominal sensitivity of 98 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-100N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary double-roll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-100N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-100N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-88F

The P. Audio "Golden Master" GM12-88F is the intersection of advanced design and state of the art manufacturing. The GM12-88F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88F is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations -general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 56 Hz Re 5.7 Ohm Qms 7.36 Qes 0.44 Qts 0.42 Bl 17.75 Tm Mms 69.33 g / 2.45 oz Mmd 62.29 g / 2.20 oz Vas 45.45 lt / 1.60 cu.ft3 Sd 531 cm2 Le 0.58 mH Cms 1.2e - 04 m/N Rms 3.4 Ns/m The P. Audio "Golden Master" GM12-88F is the intersection of advanced design and state of the art manufacturing. The GM12-88F is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The weight-optimized ferrite magnetics maximize the coil"s strengths by providing strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The ferrite magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88F is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88F"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88F is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations -general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88F offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GM12-88N

The P. Audio "Golden Master" GM12-88N is the intersection of advanced design and state of the art manufacturing. The GM12-88N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88N is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system. SMALL SIGNAL PARAMETERS Fs 63 Hz Re 5.7 Ohm Qms 3.61 Qes 0.54 Qts 0.47 Bl 17.78 Tm Mms 75.20 g / 2.65 oz Mmd 68.16 g / 2.41 oz Vas 33.5 lt / 1.18 cu.ft3 Sd 531 cm2 Le 0.50 mH Cms 8.5e - 05 m/N Rms 8.3 Ns/m The P. Audio "Golden Master" GM12-88N is the intersection of advanced design and state of the art manufacturing. The GM12-88N is a 12 inch (305mm) low frequency transducer for high performance professional audio. The 3.5 inch (88.9mm) inside/outside wound voice coil is designed for superior reliability and excursion, featuring low weight, high temperature aluminium wire and extended winding length. The low-weight neodymium magnetics maximize the coil"s strengths by providing extra strong magnetic flux across its whole range of movement. This keeps coil motion faithful to the audio signal without distorting. Aluminium "demodulation" rings negate inductance effects in the motor, further improving the fidelity of coil movement. The neodymium magnet structure cooperates with a carefully optimized venting system on the bottom of the sleek Golden Master chassis to control airflow around the voice coil. This cools the durable design to further levels of reliability without losing sensitivity - the GM12-88N is rated at 2800 W peak power handling/700 W AES continuous power handling with nominal sensitivity of 97 dB. Linear and symmetrical stiffness behavior of the suspension compliments linear coil motion. The GM12-88N"s large diameter spider is a durable silicone laminate design that provides symmetrical displacement and reliable voice coil positioning even after hours at high power levels. The cone features a proprietary doubleroll cloth surround. The perfect match of material and geometry mean ultra-low distortion of cone movement and ultra-low distortion of sound. Coating keeps the cone rigid and waterproof during operation, while low moving mass has been optimized for high performance 12" two-way designs. The ideal application for the GM12-88N is in very high performance sound reinforcement and large format public address systems. It is ideal for use in a well-tuned vented enclosure in a range of configurations - general purpose sound reinforcement systems, mid-bass applications and floor monitors. Performance is optimized when using a high pass 4th order Butterworth filter tuned near the enclosure vent frequency. The GM12-88N offers a 60-2500Hz useable bandwidth, though the actual crossover frequency will be determined by the driver and horn combination in the user"s system.

P.Audio GST12-500

The P.Audio GST12-500 is a 12 inch (305mm) diameter high performance woofer. The design utilizes a medium format 3 inch 76mm) nominal voice coil diameter with a very light weight aluminum coil configured in an inside/outside wind geometry. This light weight design, coupled with a low moving mass cone offers excellent transient response. The large format ferrite based magnet structure produces very high conversion efficiency. Inside/outside winding geometry assists in coil cooling and improves both transducer power handling and system reliability. The GST12-500 also features a very long air gap height that improves transducer linearity. The GST12-500 offers very smooth and controlled amplitude response to 2000Hz and has a useable high frequency limit of 3000Hz. The GST12-500 is an excellent choice for high output two way system designs and is ideally coupled with P.Audio BM-D series and SD series compression drivers. P.Audio offers a wide range of high frequency horns that can provide short throw or medium throw designs when coupled with the GST12-500 The design features very large diameter impregnated spiders to insure long term linearity. The impregnated spiders and very high system power handling will insure excellent long term performance. The cone is waterproof to improve reliability in high humidity environments. The GST12-500 features an aluminum die cast chassis that includes P.Audios Auto Balanced Cooling design that minimizes coil and magnet structure heating, and further improves system performance. SMALL SIGNAL PARAMETERS Re 5.5Ω Fs 56 Hz Mms 58.40 g/2.32 oz Mmd 58.40 g/2.06 oz Qms 8.34 Qes 0.51 Qts 0.48 Vas 52.86 lt/1.87 ft3 SD 552 cm2 BI 15.70 Tm Cms 1.2e-04 m/N Rms 2.78 Ns/m Le (at 1kHz) 0.52 mH The P.Audio GST12-500 is a 12 inch (305mm) diameter high performance woofer. The design utilizes a medium format 3 inch 76mm) nominal voice coil diameter with a very light weight aluminum coil configured in an inside/outside wind geometry. This light weight design, coupled with a low moving mass cone offers excellent transient response. The large format ferrite based magnet structure produces very high conversion efficiency. Inside/outside winding geometry assists in coil cooling and improves both transducer power handling and system reliability. The GST12-500 also features a very long air gap height that improves transducer linearity. The GST12-500 offers very smooth and controlled amplitude response to 2000Hz and has a useable high frequency limit of 3000Hz. The GST12-500 is an excellent choice for high output two way system designs and is ideally coupled with P.Audio BM-D series and SD series compression drivers. P.Audio offers a wide range of high frequency horns that can provide short throw or medium throw designs when coupled with the GST12-500 The design features very large diameter impregnated spiders to insure long term linearity. The impregnated spiders and very high system power handling will insure excellent long term performance. The cone is waterproof to improve reliability in high humidity environments. The GST12-500 features an aluminum die cast chassis that includes P.Audios Auto Balanced Cooling design that minimizes coil and magnet structure heating, and further improves system performance.

P.Audio P-12N

The P.Audio P-12N is a high output low frequency to mid range transducer designed with a vintage voicing. The P-12N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at from low frequencies thru the upper mid range and is ideal for high level two way and three way sound reinforcement systems. The P-12N is well suited for both live sound and recorded music venues. The operating range is 60Hz to 3000Hz. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output. The P-12N employs a large 3.9 inch (99.3mm) diameter voice coil and has been upgraded to an AES rated 1000 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. The P-12N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s precision rectangular wire technology to improve conversion efficiency and provide a large cross sectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.1Ω Fs 57 Hz Mms 79.45 g/2.80 oz Mmd 72.00 g/2.54 oz Qms 9.29 Qes 0.33 Qts 0.32 Vas 42.35 lt/1.5 ft3 SD 552 cm2 BI 20.89 Tm Cms 9.9e-05 m/N Rms 3.06 Ns/m Le (at 1kHz) 0.76 mH The P.Audio P-12N is a high output low frequency to mid range transducer designed with a vintage voicing. The P-12N is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce extremely high sound pressure levels at from low frequencies thru the upper mid range and is ideal for high level two way and three way sound reinforcement systems. The P-12N is well suited for both live sound and recorded music venues. The operating range is 60Hz to 3000Hz. The transducer uses high energy neodymium magnetics to achieve a very high acoustic output. The P-12N employs a large 3.9 inch (99.3mm) diameter voice coil and has been upgraded to an AES rated 1000 watts of continuous power handling and a full 4000 watts of peak rated power handling when sufficient amplifier headroom is available. The P-12N utilizes P.Audio"s Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P.Audio"s precision rectangular wire technology to improve conversion efficiency and provide a large cross sectional area for superior cooling. The transducer employs magnetic flux demodulation devices in the structure to increase fidelity and sonic accuracy. The system suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio SN-12MB

The SN-12MB has been designed specifically for both direct radiator and horn loaded mid bass applications. This SN Series II design has been optimized for use in the critical 60Hz to 2000Hz vocal range and is an ideal choice for professional level three way designs. A typical 12 inch design must offer both good bandwidth, down to 60Hz, and good efficiency. The SN-12MB has all of its performance designed into the 125Hz and above range. This means that the efficiency can be optimized for this frequency range. High efficiency means that lower electrical power levels are required, thus improving both system reliability and reducing power compression. The SN-12MB is a 12 inch (314mm) diameter design that employs very high energy product Neodymium magnetics to proved extremely high conversion efficiency. The medium format 3 inch (76.2mm) voice coil design is an edge wound rectangular aluminum design to further maximize efficiency. Because weight is critical for portable systems or flown/suspended designs, the SN-12MB features a die cast aluminum chassis as well as the light weight Neodymium magnet structure. The performance parameters of the SN-12MB are optimized for professional level mid bass designs. If full range designs are specified the SN-12LF should be utilized. P.Audio features state of the art design and manufacturing that insure the SN-12MB will provide very high power handling and reliability in high performance profession applications. SMALL SIGNAL PARAMETERS Fs 62 Hz Re 5.2Ω Le (at 1kHz) 0.33 mH Qms 6.70 Qes 0.44 Qts 0.41 BI 17 Tm Mms 63.36 g Vas 43.64 lt SD 0.055 m2 Eff 2.22% Hag 8 mm Hve 18 mm Xmax 5 mm The SN-12MB has been designed specifically for both direct radiator and horn loaded mid bass applications. This SN Series II design has been optimized for use in the critical 60Hz to 2000Hz vocal range and is an ideal choice for professional level three way designs. A typical 12 inch design must offer both good bandwidth, down to 60Hz, and good efficiency. The SN-12MB has all of its performance designed into the 125Hz and above range. This means that the efficiency can be optimized for this frequency range. High efficiency means that lower electrical power levels are required, thus improving both system reliability and reducing power compression. The SN-12MB is a 12 inch (314mm) diameter design that employs very high energy product Neodymium magnetics to proved extremely high conversion efficiency. The medium format 3 inch (76.2mm) voice coil design is an edge wound rectangular aluminum design to further maximize efficiency. Because weight is critical for portable systems or flown/suspended designs, the SN-12MB features a die cast aluminum chassis as well as the light weight Neodymium magnet structure. The performance parameters of the SN-12MB are optimized for professional level mid bass designs. If full range designs are specified the SN-12LF should be utilized. P.Audio features state of the art design and manufacturing that insure the SN-12MB will provide very high power handling and reliability in high performance profession applications.

P.Audio TC-150N

The P Audio TC-150N is a high output wide range transducer. The TC-150N is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce high sound pressure levels at low frequencies but also exhibits an extended high frequency response that makes the TC-150N a full range device. The operating bandwidth of the TC-100 is 80Hz-14000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The TC-150N employs a medium format 1.79 inch (45.5mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 450 watts of peak rated power handling when sufficient amplifier headroom is available. The TC-150N utilizes P Audio's under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P Audio's precision round wire technology that maximizes system conversion efficiency and cooling. The Suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.89Ω Fs 51 Hz Mms 39.18 g Mmd 31.73 g Qms 14.55 Qes 0.58 Qts 0.56 Vas 104.64 lt SD 551.5 cm2 BI 11.30 Tm Cms 2.5e-04 m/N Rms 0.87 Ns/m Le (at 1kHz) 0.46 mH The P Audio TC-150N is a high output wide range transducer. The TC-150N is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 12 inch (305mm) diameter piston will produce high sound pressure levels at low frequencies but also exhibits an extended high frequency response that makes the TC-150N a full range device. The operating bandwidth of the TC-100 is 80Hz-14000Hz. The transducer uses high energy ferrite magnetics to achieve a very high acoustic output to weight ratio. The TC-150N employs a medium format 1.79 inch (45.5mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 450 watts of peak rated power handling when sufficient amplifier headroom is available. The TC-150N utilizes P Audio's under damper venting technology to improve transducer air flow and reduce turbulence under the damper and around the voice coil. The voice coil design is a bobbin wound geometry with P Audio's precision round wire technology that maximizes system conversion efficiency and cooling. The Suspension has been designed specifically for high linear displacement and extended low frequency response. The transducer chassis is a heavy gauge stamped steel design that insures a very high degree of structural integrity.

P.Audio E10-300A

The P Audio E10-300A is a high performance wide bandwidth transducer optimized for use in mid bass frequencies. The E10-300A is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 10 inch (254mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite based magnetics to achieve a very high acoustic output to weight ratio. TheE10-300A has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 50Hz to 5000Hz. The E10-300A features a large 3 inch diameter voice coil that provides and AES rated 300 watts of continuos power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The E10-300A utilizes P Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P Audio's edge wound rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.9Ω Fs 73 Hz Mms 38.1 g/1.34 oz Mmd 34.13 g/1.2 oz Qms 6.37 Qes 0.65 Qts 0.59 Vas 23.44 lt/0.83 ft3 BI 12.59 Tm Cms 1.3e-04 m/N Rms 2.74 Ns/m Le (at 1kHz) 0.49 mH The P Audio E10-300A is a high performance wide bandwidth transducer optimized for use in mid bass frequencies. The E10-300A is an upgraded design that features many of P Audio's new technologies and performance upgrades. The 10 inch (254mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses high energy ferrite based magnetics to achieve a very high acoustic output to weight ratio. TheE10-300A has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 50Hz to 5000Hz. The E10-300A features a large 3 inch diameter voice coil that provides and AES rated 300 watts of continuos power handling and a full 1200 watts of peak rated power handling when sufficient amplifier headroom is available. The E10-300A utilizes P Audio's Auto Balanced Cooling (ABC) technology to not only improve transducer power handling and reliability but to also increase power compression performance by carefully balancing and directing airflow to critical areas. The voice coil design is a bobbin wound geometry with P Audio's edge wound rectangular wire technology to improve conversion efficiency and provide a large cross-sectional area for superior cooling. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio E8-150S

The P.Audio E8-150S is a high performance wide bandwidth transducer optimized for use in mid bass frequencies. The E8-150S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 8 inch (203mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses very high energy ferrite magnetics to achieve a high acoustic output to weight ratio. The E8-150S has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 60Hz to 3000Hz. The E8-150S features a 2 inch (51.3mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 600 watts of peak rated power handling when sufficient amplifier headroom is available. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity. SMALL SIGNAL PARAMETERS Re 5.8Ω Fs 62 Hz Mms 24.2 g/0.85 oz Mmd 22.2 g/0.78 oz Qms 2.54 Qes 0.40 Qts 0.35 Vas 19.81 lt/0.70 ft3 SD 227 cm2 BI 11.69 Tm Cms 2.7e-04 m/N Rms 3.72 Ns/m Le (at 1kHz) 0.62 mH The P.Audio E8-150S is a high performance wide bandwidth transducer optimized for use in mid bass frequencies. The E8-150S is an upgraded design that features many of P.Audio"s new technologies and performance upgrades. The 8 inch (203mm) diameter piston will produce extremely high sound pressure levels at both low and mid band frequencies and is ideal for high level response in both live sound and recorded music venues. The transducer uses very high energy ferrite magnetics to achieve a high acoustic output to weight ratio. The E8-150S has been optimized for use in two way or three way sound reinforcement systems and has an operating range of 60Hz to 3000Hz. The E8-150S features a 2 inch (51.3mm) diameter voice coil that provides an AES rated 150 watts of continuous power handling and a full 600 watts of peak rated power handling when sufficient amplifier headroom is available. The voice coil design is a bobbin wound geometry with P.Audio"s precision round wire technology to maximize system conversion efficiency. The transducer chassis is a die cast aluminum design that insures a very high degree of structural integrity.

P.Audio XT-8

The P.Audio XT-8 is a compact professional sound reinforcement system designed for foreground/background applications. The XT-8 is ideal for fixed installation applications such as restaurants, bars, retail outlets and general purpose indoor public address and full range music systems. The design of the XT-8 features a wide bandwidth 8 inch (203mm) low frequency device and a true compression driver coupled to an elliptical wave guide for controlled high frequency dispersion. The rated included angles are 90 degrees by 65 degrees. The XT-8 is a full range design that employs a high order passive crossover that provides excellent summing and balance for the individual transducer components. The XT-8 features linear amplitude response, very defined intelligibility and superior reliability. The power handling is rated at 200 watts continuous with a peak input power capability of 800 watts. Maximum peak SPL is 122dB. System impedance is rated at 8 ohms. The enclosure is constructed with high quality plywood and finished in a very durable polyurea coating. The system includes a top hat style stand adaptor and an optional U bracket to allow flexible mounting. The XT-8 is a very high performance design that features simple mounting for use in a variety of indoor applications. The P.Audio XT-8 is a compact professional sound reinforcement system designed for foreground/background applications. The XT-8 is ideal for fixed installation applications such as restaurants, bars, retail outlets and general purpose indoor public address and full range music systems. The design of the XT-8 features a wide bandwidth 8 inch (203mm) low frequency device and a true compression driver coupled to an elliptical wave guide for controlled high frequency dispersion. The rated included angles are 90 degrees by 65 degrees. The XT-8 is a full range design that employs a high order passive crossover that provides excellent summing and balance for the individual transducer components. The XT-8 features linear amplitude response, very defined intelligibility and superior reliability. The power handling is rated at 200 watts continuous with a peak input power capability of 800 watts. Maximum peak SPL is 122dB. System impedance is rated at 8 ohms. The enclosure is constructed with high quality plywood and finished in a very durable polyurea coating. The system includes a top hat style stand adaptor and an optional U bracket to allow flexible mounting. The XT-8 is a very high performance design that features simple mounting for use in a variety of indoor applications.

BRT26 Premium Install Speakers

The BRT26 is a passive, compact trapezoidal, pointsource cabinet ideally suited to background music, infill for portable and fixed installation use. The discreet design with articulated foam front and acrylic textured paint finish and multiple integrated fixing points achieves a high class look suitable for any application. The long rectangular shape of the BRT26 makes it ideal for mounting on Columns. The BRT26 is a passive, compact trapezoidal, pointsource cabinet ideally suited to background music, infill for portable and fixed installation use. The discreet design with articulated foam front and acrylic textured paint finish and multiple integrated fixing points achieves a high class look suitable for any application. The long rectangular shape of the BRT26 makes it ideal for mounting on Columns.

BRT6 Premium Install Speakers

The BRT6 is a 16 ohm passive, compact trapezoidal, point-source cabinet ideally suited to background music, infill for portable and fixed installation use. The discreet design with articulated foam front and acrylic textured paint finish and multiple integrated fixing points achieves a high class look suitable for any application. The BRT6 is a 16 ohm passive, compact trapezoidal, point-source cabinet ideally suited to background music, infill for portable and fixed installation use. The discreet design with articulated foam front and acrylic textured paint finish and multiple integrated fixing points achieves a high class look suitable for any application.

KS1 Premium Install Speakers

The KS1 is designed with a small footprint, best suited for commercial installation projects that require audio quality with minimal visual impact. The extended bass response adds extra functionality without the need of separate subwoofers. The KS1 is designed with a small footprint, best suited for commercial installation projects that require audio quality with minimal visual impact. The extended bass response adds extra functionality without the need of separate subwoofers.

KS3 Premium Install Speakers

The KS3 is designed with a small footprint, best suited for commercial installation projects that require audio quality with minimal visual impact. The extended bass response adds extra functionality without the need of separate subwoofers. The KS3 is designed with a small footprint, best suited for commercial installation projects that require audio quality with minimal visual impact. The extended bass response adds extra functionality without the need of separate subwoofers.

Zeta12T Subwoofer

The Zeta12T is a self-powered subwoofer with an in-built two channel Class-D power amplifier delivering 2 x 500W at 4 Ohms. The Zeta12T is a self-powered subwoofer with an in-built two channel Class-D power amplifier delivering 2 x 500W at 4 Ohms.

Zeta15T Subwoofer

The Zeta15T is a portable and installed PA loudspeaker that can be used for various applications including sound reinforcement in House of Ballrooms, etc. It delivers extraordinary performance at an unmatched value The Zeta15T is a portable and installed PA loudspeaker that can be used for various applications including sound reinforcement in House of Ballrooms, etc. It delivers extraordinary performance at an unmatched value

Dynatech CX-15

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The CX-15 deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The CX-15 deliver extraordinary performance at unmatched value.

DynaTech DEL-112

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

DynaTech DEL-115

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

DynaTech DEL-215

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

DynaTech DVX-125

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DVX Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DVX Series deliver extraordinary performance at unmatched value.

DynaTech DVX-225

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DVX Series (Best DJ Speakers) deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DVX Series deliver extraordinary performance at unmatched value.

DynaTech DEL-115A

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

DynaTech DEL-215A

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

DynaTech DEL-835A

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The DEL Series deliver extraordinary performance at unmatched value.

HDA-15 Active Speaker

Improving upon Dynatech's best selling active cabinet HP-15A, the HDA-15 powered loudspeaker features increased power and sensitivity, and asymmetric constant directivity to maintain wider dispersion in the nearfield, making the overall listening experience even and smooth across the venue! The HDA-15 is designed in the UK, equipped with equiplanar transducer alignment providing maximum coherence and minimum offset, and is powered by a high-performance Celestion driver. Improving upon Dynatech's best selling active cabinet HP-15A, the HDA-15 powered loudspeaker features increased power and sensitivity, and asymmetric constant directivity to maintain wider dispersion in the nearfield, making the overall listening experience even and smooth across the venue! The HDA-15 is designed in the UK, equipped with equiplanar transducer alignment providing maximum coherence and minimum offset, and is powered by a high-performance Celestion driver.

HP-10A+ Active Speakers

Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value.

HP-12A+ Active Speakers

Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value.

HP-15A+ DJ Speaker System

Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Dynatech Systems has always been dedicated in meeting the needs of sound reinforcement professionals with some of the best products available. Dynatech"s DJ Speaker Systems are one of the most renowned used by both beginners and veteran DJs across the world. Dynatech offers the industry"s most extensive and knowledgeable customer support along with high-level of technical education. Dynatech Systems are powered with AXI™ advanced asymmetric plan way high frequency horn design which delivers 90° of horizontal dispersion at the top and 100 of dispersion towards the bottom, ensuring that every listener hears the exact same sound throughout any venue. Using this advanced technology, the DJ Speaker Systems reproduce music and audio signals as they were originally captured. The wide range of DJ Speaker Systems from Dynatech are used in applications including sound reinforcement for houses of Worship, Events, Indoor Stadiums, Theme Parks, Multi-Functional Auditoriums, Schools and Transit Terminals etc. They are the best choice for live, rental and portable sound reinforcement applications. Resulting in high demand for these DJ Speaker Systems by all the audio professionals across different fields and nations. Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Dynatech Systems has always been dedicated in meeting the needs of sound reinforcement professionals with some of the best products available. Dynatech"s DJ Speaker Systems are one of the most renowned used by both beginners and veteran DJs across the world. Dynatech offers the industry"s most extensive and knowledgeable customer support along with high-level of technical education. Dynatech Systems are powered with AXI™ advanced asymmetric plan way high frequency horn design which delivers 90° of horizontal dispersion at the top and 100 of dispersion towards the bottom, ensuring that every listener hears the exact same sound throughout any venue. Using this advanced technology, the DJ Speaker Systems reproduce music and audio signals as they were originally captured. The wide range of DJ Speaker Systems from Dynatech are used in applications including sound reinforcement for houses of Worship, Events, Indoor Stadiums, Theme Parks, Multi-Functional Auditoriums, Schools and Transit Terminals etc. They are the best choice for live, rental and portable sound reinforcement applications. Resulting in high demand for these DJ Speaker Systems by all the audio professionals across different fields and nations.

HP-8A+ Active Speakers

Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback applications in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value.

HP-8WP Active Speakers

Single 8" Two way passive waterproof Speaker: Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback application in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value. Single 8" Two way passive waterproof Speaker: Portable and installed plastic loudspeakers used in applications including sound reinforcement in Front of House and Foldback application in Houses of Worship, Events, Clubs, Rehearsal Halls etc. The HP Series delivers extraordinary performance at unmatched value.

P.Audio A-100FNT

The P.Audio A-100FNT is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The A-100FNT features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The A-100FNT is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The A-100FNT offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers. The P.Audio A-100FNT is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The A-100FNT features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The A-100FNT is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The A-100FNT offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers.

P.Audio Eco-100F

The P.Audio Eco-100F is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The Eco-100F features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The Eco-100F is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The Eco-100F offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers. The P.Audio Eco-100F is a medium format foreground and background music system designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design that utilizes a wide bandwidth 6.5 inch (165mm) low frequency transducer and horn loaded high frequency radiator. The Eco-100F features a computer optimized crossover designed to provide seamless transition from low frequency to high frequency and also offer high frequency dynamic protection. The Eco-100F is ideal for applications such as restaurants, pubs, retail spaces, aerobics and fitness centers and general music and voice reproduction. The system will provide high fidelity response in installed acoustic environments. The Eco-100F offers high sensitivity and the 1 watt at 1 meter sound pressure level rating of 92dB insures ample system output even in noisy acoustic spaces. The system enclosure is available in either dark blue black and is molded using a very high quality high impact polycarbonate resin. The metal grill provides excellent protection for the system transducers.

P.Audio Gallardo-4

The P.Audio Gallardo-4 is a small format high performance sound reinforcement system designed for high quality foreground and background music applications. The Gallardo-4 is designed for both indoor and outdoor applications where music and speech reinforcement is specified. The system is ideal for use in restaurants, retail environments, bars, hotels, and other applications where high quality music systems are specified. The Gallardo-4 utilized a two element array of high output 4 inch (101.6mm) woofers. The horn loaded high frequency wave guide is positioned between the two element arrays to insure coherent and balanced high frequency response. Polar lobing is controlled by this geometry and produces a properly aimed response at the crossover frequency. The Gallardo-4 features a standard multi-tap transformer input that is switch able from a maximum of 50 watts of input power in essentially 3dB steps. The available taps are 50 watts, 25 watts, 12 watts and 5 watts. The Gallardo-4 may also be easily configured for a standard low impedance direct input. The system also features a standard mounting bracket designed for flexible aiming and easy installation. The small physical size and unique appearance of the Gallardo-4 make it an ideal installation product. It is very versatile and combines great sound with great looks. The P.Audio Gallardo-4 is a small format high performance sound reinforcement system designed for high quality foreground and background music applications. The Gallardo-4 is designed for both indoor and outdoor applications where music and speech reinforcement is specified. The system is ideal for use in restaurants, retail environments, bars, hotels, and other applications where high quality music systems are specified. The Gallardo-4 utilized a two element array of high output 4 inch (101.6mm) woofers. The horn loaded high frequency wave guide is positioned between the two element arrays to insure coherent and balanced high frequency response. Polar lobing is controlled by this geometry and produces a properly aimed response at the crossover frequency. The Gallardo-4 features a standard multi-tap transformer input that is switch able from a maximum of 50 watts of input power in essentially 3dB steps. The available taps are 50 watts, 25 watts, 12 watts and 5 watts. The Gallardo-4 may also be easily configured for a standard low impedance direct input. The system also features a standard mounting bracket designed for flexible aiming and easy installation. The small physical size and unique appearance of the Gallardo-4 make it an ideal installation product. It is very versatile and combines great sound with great looks.

P.Audio MS-50

The P.Audio MS-50 is a mini satellite home theatre speaker designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design. The P.Audio MS-50 is a mini satellite home theatre speaker designed to provide high quality music reproduction in fixed installation environments. The system is a compact two way design.

P.Audio SW-12T

The P.Audio SW-12T is a weather protected large format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The cabinet design is ported to aid low frequency extension, and the 12 inch is horn loaded to achieve higher SPL than would otherwise be possible. Within the cabinet there are 5 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 12 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in front of the woofer to a large mouthed horn. This allows the compression driver to be crossed over at a lower frequency to maintain full pattern control across the entire frequency spectrum. The large format compression driver in the SW-12T is a new design which offers extremely high SPL across the entire frequency spectrum, avoiding the need for a separate mid band and high frequency compression drivers, and still offering higher SPL. The SW-12T is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system. The P.Audio SW-12T is a weather protected large format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The cabinet design is ported to aid low frequency extension, and the 12 inch is horn loaded to achieve higher SPL than would otherwise be possible. Within the cabinet there are 5 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 12 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in front of the woofer to a large mouthed horn. This allows the compression driver to be crossed over at a lower frequency to maintain full pattern control across the entire frequency spectrum. The large format compression driver in the SW-12T is a new design which offers extremely high SPL across the entire frequency spectrum, avoiding the need for a separate mid band and high frequency compression drivers, and still offering higher SPL. The SW-12T is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system.

P.Audio SW-181S

The P.Audio SW-181S is a high output passive subwoofer designed for use outdoor with full weather protection. Its enclosure is made with rotomolded polyethylene that is water proof and UV resistant. There are 10 M10 suspension points that provide kit flexible mounting options. The grille is made from CNC punched steel and is coated with a two-layer zinc-rich powder coating. The woofer features a steel frame and a large-format voice coil. The cone material has been treated with a waterproof coating on its front and surfaces to protect against moisture intrusion and humidity. The woofer has a ferrite magnet with FEA design that provides high levels of magnetic flux. The grillw assembly is amde with three layers - a structural steel front with a dual-layer, zinc-ric powder coat; a layer of hydrophobic cloth that breaks down rainwater and forces it towards the bottom and a layer of reticulated foam that traps any moisture and allows it to evaporate. The SW-181S is appropriate for fixed installations or for event production when weather resistance is required. It has an IP rating of IP44, allowing it to be used permanently in outdoor environments. The P.Audio SW-181S is a high output passive subwoofer designed for use outdoor with full weather protection. Its enclosure is made with rotomolded polyethylene that is water proof and UV resistant. There are 10 M10 suspension points that provide kit flexible mounting options. The grille is made from CNC punched steel and is coated with a two-layer zinc-rich powder coating. The woofer features a steel frame and a large-format voice coil. The cone material has been treated with a waterproof coating on its front and surfaces to protect against moisture intrusion and humidity. The woofer has a ferrite magnet with FEA design that provides high levels of magnetic flux. The grillw assembly is amde with three layers - a structural steel front with a dual-layer, zinc-ric powder coat; a layer of hydrophobic cloth that breaks down rainwater and forces it towards the bottom and a layer of reticulated foam that traps any moisture and allows it to evaporate. The SW-181S is appropriate for fixed installations or for event production when weather resistance is required. It has an IP rating of IP44, allowing it to be used permanently in outdoor environments.

P.Audio SW-6C

The P.Audio SW-6C is a weather protected small format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The enclosure features a 35mm pole mount socket to mount of top of a standard speaker pole. The cabinet design is ported to aid low frequency extension. Within the cabinet there are 3 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 6 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in behind the woofer in a Thru Pole Piece design. The horn flare ensures even coverage of 90 x 90 degrees. The high frequency driver uses a separate magnet in order to increase flux density in the magnetic gap, to benefit overall SPL and high frequency extension. The SW-6C is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system. The P.Audio SW-6C is a weather protected small format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The enclosure features a 35mm pole mount socket to mount of top of a standard speaker pole. The cabinet design is ported to aid low frequency extension. Within the cabinet there are 3 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 6 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in behind the woofer in a Thru Pole Piece design. The horn flare ensures even coverage of 90 x 90 degrees. The high frequency driver uses a separate magnet in order to increase flux density in the magnetic gap, to benefit overall SPL and high frequency extension. The SW-6C is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system.

P.Audio SW-8C

The P.Audio SW-8C is a weather protected medium format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The enclosure features a 35mm pole mount socket to mount of top of a standard speaker pole. The cabinet design is ported to aid low frequency extension, and the 8 inch is horn loaded to achieve higher SPL than would otherwise be possible. Within the cabinet there are 5 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 8 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in front of the woofer to a large mouthed horn. This allows the compression driver to be crossed over at a lower frequency to maintain full pattern control across the entire frequency spectrum. The SW-8C is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system. The P.Audio SW-8C is a weather protected medium format sound reinforcement system. The cabinet is made from a one piece rotomolded UV resistant polyethylene enclosure. The enclosure features a 35mm pole mount socket to mount of top of a standard speaker pole. The cabinet design is ported to aid low frequency extension, and the 8 inch is horn loaded to achieve higher SPL than would otherwise be possible. Within the cabinet there are 5 integrated rigging points, which can be used in conjunction with the included U Bracket kit for mounting to walls or ceilings. When pole mounting is required, an optional Pole Mount Kit can be purchased. The grille is made from CNC punched steel, and coated in a two-layer zinc rich, UV resistant powder coat finish. The 8 inch woofer has a treated cone paper pulp for resistance against water and against dry rot. The high energy ferrite magnetics ensure high SPL for maximum coverage from a small system. The high frequency driver is mounted in front of the woofer to a large mouthed horn. This allows the compression driver to be crossed over at a lower frequency to maintain full pattern control across the entire frequency spectrum. The SW-8C is well suited to outdoor environments where a reliable, weatherproof system is specified. The line matching transformer allows connection to a high voltage line to minimise cable losses over long cable runs, further improving the usability of the system.

P.Audio TH-300

The P.Audio TH-300 is a very high output paging system that features 4 PA-D110 compression drivers in a manifold configuration. This configu-ration allows the 4 drivers to sum into the TH-300 reentrant wide range horn. The TH-300 is rated for a program power of a full 300 watts and con-tinuous operation of 200 watts. The system has been subjected to accelerated life tests for over 100 hours of non-stop operation. This reliability and power handling allow the TH-300 to produce over 130dB of sound pressure level at one meter. This provided excellent throw in large spaces. The TH-300 has a rated bandwidth of 200Hz to 7 kHz and is ideal for both vocal fundamentals as well as critical vocal harmonics. The extended band-width provides excellent intelligibility and vocal clarity. The TH-300 is avai-lable in either 8 ohm or 16 ohm versions. The 16 ohm version is ideal for applications where multiple TH-300 paging systems are specified in parallel for larger coverage applications. The system is provided with an integral mounting bracket for fast and easy installation. The TH-300 is weather resistant and ideal for use in both outdoor and indoor applications where voice range paging is required. The TH-300 is a large format design designed for high power and high sound pressure level applications. The P.Audio TH-300 is a very high output paging system that features 4 PA-D110 compression drivers in a manifold configuration. This configu-ration allows the 4 drivers to sum into the TH-300 reentrant wide range horn. The TH-300 is rated for a program power of a full 300 watts and con-tinuous operation of 200 watts. The system has been subjected to accelerated life tests for over 100 hours of non-stop operation. This reliability and power handling allow the TH-300 to produce over 130dB of sound pressure level at one meter. This provided excellent throw in large spaces. The TH-300 has a rated bandwidth of 200Hz to 7 kHz and is ideal for both vocal fundamentals as well as critical vocal harmonics. The extended band-width provides excellent intelligibility and vocal clarity. The TH-300 is avai-lable in either 8 ohm or 16 ohm versions. The 16 ohm version is ideal for applications where multiple TH-300 paging systems are specified in parallel for larger coverage applications. The system is provided with an integral mounting bracket for fast and easy installation. The TH-300 is weather resistant and ideal for use in both outdoor and indoor applications where voice range paging is required. The TH-300 is a large format design designed for high power and high sound pressure level applications.

P.Audio X9-15A

The P Audio X9 Sound Reinforcement System is a very high output bi-amplified powered loudspeaker designed to provide excellent fidelity, intelligibility and high output while maintaining ultra high reliability. The X9 is a fully powered design that features a class D low frequency module that generates 1000 watts of peak power and 500 watts of continuous power. The high frequency section is driven by a class D amplifier that delivers 200 watts of peak power and 100 watts of continuous power. The X9 design incorporates a matched set of high order active filters that provide 4th order crossovers that have been optimized for both the low frequency and high frequency transducer sections. The input pre amplifier features active equalization that optimizes the amplitude response of each pass band. The on-board peak limiter is precisely calibrated to provide maximum clean output power. The amplifier section also features a 4th order high pass filter located in the low pass filter block to insure maximum system dynamics and system excursion control. The X9 input section features professional mixer style XLR mic level and line level inputs. Both inputs are electronically balanced. The X9 also includes a line level RCA input. The mic level and line level inputs include user adjustable gain functions. The system also features an XLR thru to allow multiple X9 systems to be utilized in larger venues. In addition to fully adjustable mic and line level controls, the X9 also includes both low shelving and high shelving style equalization. The P Audio X9 Sound Reinforcement System is a very high output bi-amplified powered loudspeaker designed to provide excellent fidelity, intelligibility and high output while maintaining ultra high reliability. The X9 is a fully powered design that features a class D low frequency module that generates 1000 watts of peak power and 500 watts of continuous power. The high frequency section is driven by a class D amplifier that delivers 200 watts of peak power and 100 watts of continuous power. The X9 design incorporates a matched set of high order active filters that provide 4th order crossovers that have been optimized for both the low frequency and high frequency transducer sections. The input pre amplifier features active equalization that optimizes the amplitude response of each pass band. The on-board peak limiter is precisely calibrated to provide maximum clean output power. The amplifier section also features a 4th order high pass filter located in the low pass filter block to insure maximum system dynamics and system excursion control. The X9 input section features professional mixer style XLR mic level and line level inputs. Both inputs are electronically balanced. The X9 also includes a line level RCA input. The mic level and line level inputs include user adjustable gain functions. The system also features an XLR thru to allow multiple X9 systems to be utilized in larger venues. In addition to fully adjustable mic and line level controls, the X9 also includes both low shelving and high shelving style equalization.

P.Audio X9-18A

The P Audio X9 Sub is a high output professional active sub woofer designed to provide extended low frequency output at very high sound pressure levels. The X9 Sub is an excellent match for the X9 Sub enclosure but may be used with a variety of other sound reinforcement top/full range enclosures. The X9 Sub is powered by a high peak power linear amplifier that exhibits excellent dynamic power. The amplifier is rated at a full 1200 watts of peak power. The amplifier employs a fast peak limiter circuit to insure high dynamic range coupled with excellent system protection. The X9 Sub bandwidth is 40Hz to 80Hz and insures high impact low frequency performance that is ideal for live performance venues, pubs, night clubs and high impact music venues. The X9 Sub also utilizes a Phase Control circuit that allows the user to adjust phase within a 0 degree to 180 degree range. This function is used when the top enclosure is not physically located directly above the X9 Sub and allows the entire system to achieve acoustic summing. The P Audio X9 Sub is a high output professional active sub woofer designed to provide extended low frequency output at very high sound pressure levels. The X9 Sub is an excellent match for the X9 Sub enclosure but may be used with a variety of other sound reinforcement top/full range enclosures. The X9 Sub is powered by a high peak power linear amplifier that exhibits excellent dynamic power. The amplifier is rated at a full 1200 watts of peak power. The amplifier employs a fast peak limiter circuit to insure high dynamic range coupled with excellent system protection. The X9 Sub bandwidth is 40Hz to 80Hz and insures high impact low frequency performance that is ideal for live performance venues, pubs, night clubs and high impact music venues. The X9 Sub also utilizes a Phase Control circuit that allows the user to adjust phase within a 0 degree to 180 degree range. This function is used when the top enclosure is not physically located directly above the X9 Sub and allows the entire system to achieve acoustic summing.

P.Audio XE-12

The P.Audio XE-12 provides a cost effective background and foreground sound reinforcement solution to both portable and fixed install applications. The 12" woofer provides high intelligibility and extended low frequency response in a convenient, small profile design. The XE-12 is ideal for background music applications in pubs, bars, restaurants and retail outlets, as well as foreground full range music systems. The 1" true compression driver in the XE-12 features very high reliability, and is coupled to a 90 x 65 degree elliptical wave guide for controlled and detailed high frequency performance The passive network in XE-12 balances the output from both transducer components and provides optimal summing in the mid band region. The power handling is rated at 200 watts continuous with a peak input power of 800 watts. Cabinet construction is of high quality wood with internal supports for extra rigidity, and is finished with high quality black paint. The XE-12 is a high performance design with superior vocal intelligibility from the high quality P.Audio components. The P.Audio XE-12 provides a cost effective background and foreground sound reinforcement solution to both portable and fixed install applications. The 12" woofer provides high intelligibility and extended low frequency response in a convenient, small profile design. The XE-12 is ideal for background music applications in pubs, bars, restaurants and retail outlets, as well as foreground full range music systems. The 1" true compression driver in the XE-12 features very high reliability, and is coupled to a 90 x 65 degree elliptical wave guide for controlled and detailed high frequency performance The passive network in XE-12 balances the output from both transducer components and provides optimal summing in the mid band region. The power handling is rated at 200 watts continuous with a peak input power of 800 watts. Cabinet construction is of high quality wood with internal supports for extra rigidity, and is finished with high quality black paint. The XE-12 is a high performance design with superior vocal intelligibility from the high quality P.Audio components.

P.Audio XE-15

The P.Audio XE-15 provides a cost effective background and foreground sound reinforcement solution to both portable and fixed install applications. The 15" woofer provides high intelligibility and extended low frequency response in a convenient, medium profile design. The XE-15 is ideal for background music applications in pubs, bars, restaurants and retail outlets, as well as foreground full range music systems. The 1" true compression driver in the XE-15 features very high reliability, and is coupled to a 90 x 65 degree elliptical wave guide for controlled and detailed high frequency performance The passive network in XE-15 balances the output from both transducer components and provides optimal summing in the mid band region. The power handling is rated at 250 watts continuous with a peak input power of 1000 watts. Cabinet construction is of high quality wood with internal supports for extra rigidity, and is finished with high quality black paint. The XE-15 is a high performance design with superior vocal intelligibility from the high quality P.Audio components. The P.Audio XE-15 provides a cost effective background and foreground sound reinforcement solution to both portable and fixed install applications. The 15" woofer provides high intelligibility and extended low frequency response in a convenient, medium profile design. The XE-15 is ideal for background music applications in pubs, bars, restaurants and retail outlets, as well as foreground full range music systems. The 1" true compression driver in the XE-15 features very high reliability, and is coupled to a 90 x 65 degree elliptical wave guide for controlled and detailed high frequency performance The passive network in XE-15 balances the output from both transducer components and provides optimal summing in the mid band region. The power handling is rated at 250 watts continuous with a peak input power of 1000 watts. Cabinet construction is of high quality wood with internal supports for extra rigidity, and is finished with high quality black paint. The XE-15 is a high performance design with superior vocal intelligibility from the high quality P.Audio components.

P.Audio XT-10

The P.Audio XT-10 is a compact professional sound reinforcement system designed for foreground/background applications. The 10 inch (254mm) low frequency woofer offers extended low frequency response in a very small profile design. The XT-10 is ideal for fixed installation applications such as restaurants, bars, retail outlets and general purpose indoor public address and full range music systems. The 10 inch design provides superior music range performance and extended bandwidth for applications that specify enhanced music content. The design of the XT-10 features a wide bandwidth 10 inch (254mm) low frequency device and a true compression driver coupled to an elliptical wave guide for controlled high frequency dispersion. The rated included angles are 90 degrees by 65 degrees. The P.Audio XT-10 is a compact professional sound reinforcement system designed for foreground/background applications. The 10 inch (254mm) low frequency woofer offers extended low frequency response in a very small profile design. The XT-10 is ideal for fixed installation applications such as restaurants, bars, retail outlets and general purpose indoor public address and full range music systems. The 10 inch design provides superior music range performance and extended bandwidth for applications that specify enhanced music content. The design of the XT-10 features a wide bandwidth 10 inch (254mm) low frequency device and a true compression driver coupled to an elliptical wave guide for controlled high frequency dispersion. The rated included angles are 90 degrees by 65 degrees.

P.Audio XT-12

The P.Audio XT-12 is a compact professional sound reinforcement system designed for both foreground and background applications. The 12 inch (305mm) low frequency woofer offers extended low frequency response in a narrow profile design. The large 44mm compression driver with titanium diaphragm, coupled to the aluminium 90x40 horn offers superb transient response and controlled dispersion. The XT-12 is ideal for fixed installation applications such as restaurants, bars and general purpose public address and full range music systems. The XT-12 is a full range design that employs 3rd order passive networks for excellent summing and balance for the individual components and offering a higher degree of reliability. The power handling is rated at 250w continuous with a peak input power capability of 1000 watts. System impedance is rated at 8 ohms. The enclosure is a very high quality plywood and finished in a very durable polyurea coating. The system includes a top hat system and an optional U bracket to allow fixed installation. The XT-12 may also be suspended using the P.Audio M10 Eye Bolt Kit. The XT-12 is a very high performance design that features simple mounting options for use in a variety of indoor applications. The P.Audio XT-12 is a compact professional sound reinforcement system designed for both foreground and background applications. The 12 inch (305mm) low frequency woofer offers extended low frequency response in a narrow profile design. The large 44mm compression driver with titanium diaphragm, coupled to the aluminium 90x40 horn offers superb transient response and controlled dispersion. The XT-12 is ideal for fixed installation applications such as restaurants, bars and general purpose public address and full range music systems. The XT-12 is a full range design that employs 3rd order passive networks for excellent summing and balance for the individual components and offering a higher degree of reliability. The power handling is rated at 250w continuous with a peak input power capability of 1000 watts. System impedance is rated at 8 ohms. The enclosure is a very high quality plywood and finished in a very durable polyurea coating. The system includes a top hat system and an optional U bracket to allow fixed installation. The XT-12 may also be suspended using the P.Audio M10 Eye Bolt Kit. The XT-12 is a very high performance design that features simple mounting options for use in a variety of indoor applications.

P.Audio XT-15

The P.Audio XT-15 is a compact professional sound reinforcement system designed for both foreground and background applications. The 15 inch (381mm) low frequency woofer offers extended low frequency response in a narrow profile design. The large 44mm compression driver with titanium diaphragm, coupled to the aluminium 90x40 horn offers superb transient response and controlled dispersion. The XT-15 is ideal for fixed installation applications such as restaurants, bars and general purpose public address and full range music systems. The XT-15 is a full range design that employs high order passive networks for excellent summing and balance for the individual components and offering a higher degree of reliability. The power handling is rated at 400w continuous with a peak input power capability of 1600 watts. System impedance is rated at 8 ohms. The enclosure is a very high quality plywood and finished in a very durable polyurea coating. The system includes a top hat system and an optional U bracket to allow fixed installation. The XT-15 may also be suspended using the P.Audio M10 Eye Bolt Kit. The XT-15 is a very high performance design that features simple mounting options for use in a variety of indoor applications. The P.Audio XT-15 is a compact professional sound reinforcement system designed for both foreground and background applications. The 15 inch (381mm) low frequency woofer offers extended low frequency response in a narrow profile design. The large 44mm compression driver with titanium diaphragm, coupled to the aluminium 90x40 horn offers superb transient response and controlled dispersion. The XT-15 is ideal for fixed installation applications such as restaurants, bars and general purpose public address and full range music systems. The XT-15 is a full range design that employs high order passive networks for excellent summing and balance for the individual components and offering a higher degree of reliability. The power handling is rated at 400w continuous with a peak input power capability of 1600 watts. System impedance is rated at 8 ohms. The enclosure is a very high quality plywood and finished in a very durable polyurea coating. The system includes a top hat system and an optional U bracket to allow fixed installation. The XT-15 may also be suspended using the P.Audio M10 Eye Bolt Kit. The XT-15 is a very high performance design that features simple mounting options for use in a variety of indoor applications.

P.Audio 2Line-6

The P.Audio 2LINE-6 is an six element vertical column array. The 2LINE-6 exhibits progressive directivity control and is an excellent choice for use in reverberant spaces where very controlled and defined vertical radiation is required. The enclosure is a passive design that features high power handling and reliability. The vertical column array consists of six high output, high excursion two inch (51mm) closely spaced dynamic transducers. The close physical spacing insures controlled polar lobing and tight pattern control. The acoustic performance of the 2LINE-6 make it an ideal choice for houses of worship, theaters, commercial venues, airports, and gathering spaces of all sizes. The P.Audio 2LINE-6 is available in both black and white finishes, and is a heavy duty steel enclosure, with steel grill. The cabinet is both zinc plated and powder coated to ensure durability. The input is 2 x Neutrik speakon connectors to allow easy daisy chaining of cabinets. The 2LINE-6 features a rear mounted switch for changing system impedance between 4 and 16 ohms. The 4 ohm setting is intended for use when maximum amplifier power is to be delivered to a single cabinet, or for when the 2LINE-6 is used with the accompanying 2LINE-Sub. The 16 ohm setting allows 4 cabinets to be parallel linked, when a 4 ohm stable amplifier is used. The 16 ohm setting can be used with the accompanying 2LINE-Sub for lower power situations. The 2LINE-Sub high performance subwoofer is optimised for accurate mid-low reproduction, allowing more headroom for the 2LINE-6 column loudspeaker. Without the subwoofer, it is highly recommended that a high pass filter is set at 200Hz (24dB/oct) to ensure no damage to the 2LINE-6 loudspeaker. P.Audio offers a variety of rigging accessories for use within the 2LINE system. When used with the accompanying subwoofer, the 2L-Pole and 2L-PSA allow the 2LINE-6 enclosure to be mounted above the subwoofer at a fixed height. The 2L-PSA features 2 tilt settings either 0 degrees or 10 degrees down tilt to optimise the radiation for the acoustic space. A single or two column array may be mounted using the 2L-PT and 2L-LB brackets. The 2L-PT allows solid wall mounting with up to 60 degrees pan capability and up to 15 degrees down-tilt capability. The 2L-LB can then be used to join two enclosures together, with inter-cabinet tilt capability up to 15 degrees. The P.Audio 2LINE-6 is an six element vertical column array. The 2LINE-6 exhibits progressive directivity control and is an excellent choice for use in reverberant spaces where very controlled and defined vertical radiation is required. The enclosure is a passive design that features high power handling and reliability. The vertical column array consists of six high output, high excursion two inch (51mm) closely spaced dynamic transducers. The close physical spacing insures controlled polar lobing and tight pattern control. The acoustic performance of the 2LINE-6 make it an ideal choice for houses of worship, theaters, commercial venues, airports, and gathering spaces of all sizes. The P.Audio 2LINE-6 is available in both black and white finishes, and is a heavy duty steel enclosure, with steel grill. The cabinet is both zinc plated and powder coated to ensure durability. The input is 2 x Neutrik speakon connectors to allow easy daisy chaining of cabinets. The 2LINE-6 features a rear mounted switch for changing system impedance between 4 and 16 ohms. The 4 ohm setting is intended for use when maximum amplifier power is to be delivered to a single cabinet, or for when the 2LINE-6 is used with the accompanying 2LINE-Sub. The 16 ohm setting allows 4 cabinets to be parallel linked, when a 4 ohm stable amplifier is used. The 16 ohm setting can be used with the accompanying 2LINE-Sub for lower power situations. The 2LINE-Sub high performance subwoofer is optimised for accurate mid-low reproduction, allowing more headroom for the 2LINE-6 column loudspeaker. Without the subwoofer, it is highly recommended that a high pass filter is set at 200Hz (24dB/oct) to ensure no damage to the 2LINE-6 loudspeaker. P.Audio offers a variety of rigging accessories for use within the 2LINE system. When used with the accompanying subwoofer, the 2L-Pole and 2L-PSA allow the 2LINE-6 enclosure to be mounted above the subwoofer at a fixed height. The 2L-PSA features 2 tilt settings either 0 degrees or 10 degrees down tilt to optimise the radiation for the acoustic space. A single or two column array may be mounted using the 2L-PT and 2L-LB brackets. The 2L-PT allows solid wall mounting with up to 60 degrees pan capability and up to 15 degrees down-tilt capability. The 2L-LB can then be used to join two enclosures together, with inter-cabinet tilt capability up to 15 degrees.

P.Audio 2Line-Sub

The P.Audio 2LINE-Sub is an actively driven 10 wooden subwoofer enclosure. The 2LINE-Sub is ideal for use in both portable and fixed installation environments where low frequency extension is desired. The amplifier is a class D design, with universal Switch Mode Power Supply (SMPS). The amplifier output is 300w to drive the 10 transducer component. The amplifier also has a 300w (4 ohm) output available to drive the 2LINE-6 column loudspeaker or other loudspeaker of choice. The 8 switchable EQ presets found on the amplifier panel of the 2LINE-Sub allow different voicing modes with the 2LINE-6, including 1 preset optimised for use with spoken word. For ease of use, the XLR input on the 2LINE-Sub has switchable sensitivity to allow either line level signals or a microphone to be plugged straight into the system. A THRU XLR output is also present, to allow easy system scalability. The cabinet construction is of a heavy duty wood, with thick splatter coat of paint for ultimate durability and easy touch up of cosmetics. The transducer component is a ferrite 10woofer with highly linear suspension design to ensure low distortion and high excursion capabilities. Two recessed handles on the side of the cabinet allow easy portability. The highly rigid steel grill ensures the transducer is protected at all times. 4 Rubber feet on the bottom of the enclosure ensure the sub will not move, and the M20 thread speaker pole mount on the top of the enclosure allows easy system set up when used with the 2L-Pole and 2L-PSA accessories, in order to create a well-balanced 2LINE System. The P.Audio 2LINE-Sub is an actively driven 10 wooden subwoofer enclosure. The 2LINE-Sub is ideal for use in both portable and fixed installation environments where low frequency extension is desired. The amplifier is a class D design, with universal Switch Mode Power Supply (SMPS). The amplifier output is 300w to drive the 10 transducer component. The amplifier also has a 300w (4 ohm) output available to drive the 2LINE-6 column loudspeaker or other loudspeaker of choice. The 8 switchable EQ presets found on the amplifier panel of the 2LINE-Sub allow different voicing modes with the 2LINE-6, including 1 preset optimised for use with spoken word. For ease of use, the XLR input on the 2LINE-Sub has switchable sensitivity to allow either line level signals or a microphone to be plugged straight into the system. A THRU XLR output is also present, to allow easy system scalability. The cabinet construction is of a heavy duty wood, with thick splatter coat of paint for ultimate durability and easy touch up of cosmetics. The transducer component is a ferrite 10woofer with highly linear suspension design to ensure low distortion and high excursion capabilities. Two recessed handles on the side of the cabinet allow easy portability. The highly rigid steel grill ensures the transducer is protected at all times. 4 Rubber feet on the bottom of the enclosure ensure the sub will not move, and the M20 thread speaker pole mount on the top of the enclosure allows easy system set up when used with the 2L-Pole and 2L-PSA accessories, in order to create a well-balanced 2LINE System.

Dynatech Y-15 Two-Way Monitor afsa

Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The Y-15 deliver extraordinary performance at unmatched value. Portable and installed PA loudspeakers used in applications including sound reinforcement in Houses of Worship, Events, Clubs, Rehearsal Halls and Ballrooms etc. The Y-15 deliver extraordinary performance at unmatched value.

P.Audio CL35-BMD

The P.Audio CL35-BMD is a high frequency wave guide coupled to a BM-D740 high output compression driver. The converging lens wave guide and compression driver are designed for use in line array sound reinforcement systems or whenever planar wave-fronts are required. The CL35-BMD produces extremely coherent output with a rated frequency range of 1000Hz to 16kHz. The CL35-BMD may be used as a single device in planar front sound reinforcement systems or be stacked vertically in a two high configuration for very high output line array system designs. Applications information may be found in the P.Audio white paper titled "CL Wave Guide Applications" in the "High Frequency" section of the P.Audio web site. (www.paudiothailand.com). This white paper describes basic 90 degree and 120 degree horizontal pattern control configurations typical in modern line array system designs. The CL35-BMD is a converging acoustic lens design that achieves excellent time coherence over the entire front of the wave guide "mouth". This converging acoustic lens design acts to convert the naturally diverging spherical wave fronts found in typical wave guides to a more planar, time coherent wave front suitable for use in large format or arrayed linear geometry loudspeaker system designs. The physical design of the horizontal exit width allows for the addition of customer configured horizontal radiation control boundaries of up to 120 degrees. The addition of simple mounting holes in the front flanges allow the customer supplied control boundary (horn) to be easily mounted to the CL35-BMD. The recommended low frequency limit of the device is 1000Hz. Although the flare rate of the device is a lower frequency, 1000Hz is recommended to provide both good loading and reliability to the selected compression driver. The CL35-BMD is a rugged die cast aluminum design that couples to the large format ferrite based BM-D740. This thick wall dies cast aluminum design offers both excellent mechanical rigidity and superior structural support for the BMD large format compression driver. The CL35-BMD is an excellent high frequency addition for conventional two way and three way single enclosure designs and can be easily combined to stack in multiple vertical configurations. The edge to edge physical spacing of the wave guide allow for superior coupling at very high frequencies.

P.Audio PH-2380

The PH-2380 is a 2 inch (50 mm) throat high frequency horn. The PH-2380 is a horizontal format horn with a 17.5 inch (443mm) wide by 11 inch (280mm) mouth. This large horn mouth insures excellent pattern control down to below 1000Hz. The rated horizontal coverage angle is 90 degree and the vertical coverage is 40 degree. This set of included angles makes the PH-2380 an excellent choice for two way sound reinforcement systems. The 2 inch throat diameter is an industry standard that is designed to mate to many of the P Audio PreNeo and BMD professional compression drivers. The PH-2380 is constructed of very high impact ABS with a glass filling to insure additional stability and structural rigidity.The large throat diameter makes the PH-2380 an ideal device for reproduction of low distortion vocal material and general mid band program material. Excellent acoustic loading allow the horn to be used to below 1000Hz. The PH-2380 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver ) - BM-D750 - PreNeo-750N The PH-2380 is a 2 inch (50 mm) throat high frequency horn. The PH-2380 is a horizontal format horn with a 17.5 inch (443mm) wide by 11 inch (280mm) mouth. This large horn mouth insures excellent pattern control down to below 1000Hz. The rated horizontal coverage angle is 90 degree and the vertical coverage is 40 degree. This set of included angles makes the PH-2380 an excellent choice for two way sound reinforcement systems. The 2 inch throat diameter is an industry standard that is designed to mate to many of the P Audio PreNeo and BMD professional compression drivers. The PH-2380 is constructed of very high impact ABS with a glass filling to insure additional stability and structural rigidity.The large throat diameter makes the PH-2380 an ideal device for reproduction of low distortion vocal material and general mid band program material. Excellent acoustic loading allow the horn to be used to below 1000Hz. The PH-2380 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver ) - BM-D750 - PreNeo-750N

P.Audio PH-2723

The PH-2723 is a large format throat high frequency horn. The 2 inch (50 mm) design is optimized for high pressure mid band response. The PH-2723 is compatible with a variety of P.Audio PreNeo and BMD series professional compression drivers. The rated coverage angles of 60 for medium to long throw high output applications. Because the 2 inch throat diameter is an industry standard, the PH-2723 may be used with many competitive compression drivers as well. The horn construction is a high impact ABS with glass filling to provide superior structural support for the compression driver. The PH-2723 is designed for use in high output professional sound reinforcement systems where long throw is specified. The horn is also ideal for applications where very specific acoustic coverage areas are specified. Excellent acoustic loading allows the horn to be used to below 1000Hz. The PH-2723 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver ) - BM-D750 - PreNeo-750N The PH-2723 is a large format throat high frequency horn. The 2 inch (50 mm) design is optimized for high pressure mid band response. The PH-2723 is compatible with a variety of P.Audio PreNeo and BMD series professional compression drivers. The rated coverage angles of 60 for medium to long throw high output applications. Because the 2 inch throat diameter is an industry standard, the PH-2723 may be used with many competitive compression drivers as well. The horn construction is a high impact ABS with glass filling to provide superior structural support for the compression driver. The PH-2723 is designed for use in high output professional sound reinforcement systems where long throw is specified. The horn is also ideal for applications where very specific acoustic coverage areas are specified. Excellent acoustic loading allows the horn to be used to below 1000Hz. The PH-2723 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver ) - BM-D750 - PreNeo-750N

P.Audio PH-3220

The PH-3220 is a medium format high frequency horn designed for use in professional sound reinforcement systems. The PH-3220 has a nominally rated radiation pattern of 100 degree horizontal by 60 degree vertical. This rated coverage pattern makes the horn and ideal choice for use in high level two way 12 inch or 15 inch system designs. The rectangular mouth geometry allows for a wide horizontal coverage and the mouth horizontal dimension maintains excellent coverage control to below 1000Hz. The PH-3220 features a 1 inch (25.4mm) diameter bolt on throat design. This 1 inch diameter design allows many of the P Audio PreNeo and BMD series professional compression drivers to be coupled to the horn. Because the 1 inch throat is an industry standard, the PH-3220 is also compatible with a wide variety of competitive professional level compression drivers. The PH-3220 is a rugged and structurally sound injection molded design. A very high impact ABS resin utilizing glass filler provides a high degree of structural support for the compression driver. The PH-3220 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver) - BM-D440 - BM-D450 - PreNeo-450N - PA-DE34 The PH-3220 is a medium format high frequency horn designed for use in professional sound reinforcement systems. The PH-3220 has a nominally rated radiation pattern of 100 degree horizontal by 60 degree vertical. This rated coverage pattern makes the horn and ideal choice for use in high level two way 12 inch or 15 inch system designs. The rectangular mouth geometry allows for a wide horizontal coverage and the mouth horizontal dimension maintains excellent coverage control to below 1000Hz. The PH-3220 features a 1 inch (25.4mm) diameter bolt on throat design. This 1 inch diameter design allows many of the P Audio PreNeo and BMD series professional compression drivers to be coupled to the horn. Because the 1 inch throat is an industry standard, the PH-3220 is also compatible with a wide variety of competitive professional level compression drivers. The PH-3220 is a rugged and structurally sound injection molded design. A very high impact ABS resin utilizing glass filler provides a high degree of structural support for the compression driver. The PH-3220 may be used with the following P.audio professional compression drivers. (or any industry standard compatible driver) - BM-D440 - BM-D450 - PreNeo-450N - PA-DE34

P.Audio PHT-404P

The P.Audio PHT-404P is an integrated high frequency horn and compression driver. The design yields very extended high frequency response and controlled directivity in a rectangular geometry. The rated coverage pattern is 100 degree horizontal by 60 degree vertical. This rated coverage pattern is ideal for short throw applications such as foreground and background music system designs found in restaurants, pubs, and retail environments. The PHT-404P has a rated bandwidth of 3kHz to beyond 16kHz. This frequency response range makes the system excellent for wide coverage upper midrange and high frequency operation. The PHT-404P is ideally mated with a 10 inch, or 8 inch low frequency loudspeaker in a two way design. The PHT-404P features a 1 inch diameter (25.4mm) phenolic based diaphragm assembly. The small format (1 inch) diaphragm is ideal for maintaining piston range performance in the upper frequency range. The wide horizontal mouth (10.6 inches, 269mm) maintains very good horizontal coverage control. The high sensitivity of 105 dB (1 watt at 1 meter) allows the PHT-404P to be used in medium sized venues. The horn is made of a rugged glass filed ABS plastic resin and the critical compression driver components are all controlled by P.Audio"s advanced quality and manufacturing systems. The P.Audio PHT-404P is an integrated high frequency horn and compression driver. The design yields very extended high frequency response and controlled directivity in a rectangular geometry. The rated coverage pattern is 100 degree horizontal by 60 degree vertical. This rated coverage pattern is ideal for short throw applications such as foreground and background music system designs found in restaurants, pubs, and retail environments. The PHT-404P has a rated bandwidth of 3kHz to beyond 16kHz. This frequency response range makes the system excellent for wide coverage upper midrange and high frequency operation. The PHT-404P is ideally mated with a 10 inch, or 8 inch low frequency loudspeaker in a two way design. The PHT-404P features a 1 inch diameter (25.4mm) phenolic based diaphragm assembly. The small format (1 inch) diaphragm is ideal for maintaining piston range performance in the upper frequency range. The wide horizontal mouth (10.6 inches, 269mm) maintains very good horizontal coverage control. The high sensitivity of 105 dB (1 watt at 1 meter) allows the PHT-404P to be used in medium sized venues. The horn is made of a rugged glass filed ABS plastic resin and the critical compression driver components are all controlled by P.Audio"s advanced quality and manufacturing systems.

P.Audio PHT-408

The PHT-408 is a rectangular format high output integrated horn and driver. The system features a high sensitivity rating of 105dB at one watt and one meter. This makes the PHT-408 ideal for portable sound reinforcement system applications. The PHT-408 has been used very successfully in two way designs where the low frequency loudspeaker is a 12 inch or 15 inch professional quality transducer. The integrated horn and driver is used in many professional two way designs. The rated bandwidth of 2kHz to beyond 16kHz make this system ideal for two way system designs. The PHT-408 is ideal as a high frequency device for portable high performance sound reinforcement systems. The P.Audio PHT-408 uses a small format diaphragm assembly that is optimized for wide band piston range response. This diaphragm format makes the compression driver perform well at extremely high frequencies. The rated coverage pattern offers included angles of 90 degree in the horizontal plane and 40 degree in the vertical plane. This dispersion pattern is ideal for wide coverage applications such as night clubs, pubs, and restaurant applications. The PHT-408 is a rectangular format high output integrated horn and driver. The system features a high sensitivity rating of 105dB at one watt and one meter. This makes the PHT-408 ideal for portable sound reinforcement system applications. The PHT-408 has been used very successfully in two way designs where the low frequency loudspeaker is a 12 inch or 15 inch professional quality transducer. The integrated horn and driver is used in many professional two way designs. The rated bandwidth of 2kHz to beyond 16kHz make this system ideal for two way system designs. The PHT-408 is ideal as a high frequency device for portable high performance sound reinforcement systems. The P.Audio PHT-408 uses a small format diaphragm assembly that is optimized for wide band piston range response. This diaphragm format makes the compression driver perform well at extremely high frequencies. The rated coverage pattern offers included angles of 90 degree in the horizontal plane and 40 degree in the vertical plane. This dispersion pattern is ideal for wide coverage applications such as night clubs, pubs, and restaurant applications.

P.Audio PST-888

The PST-888 is a super tweeter. The system features a high sensitivity rating of 108dB at one watt and one meter. This makes the PST-888 ideal for portable sound reinforcement system applications. The rated bandwidth of 2kHz to beyond 15kHz make this system ideal for two way system designs. The PST-888 is a super tweeter. The system features a high sensitivity rating of 108dB at one watt and one meter. This makes the PST-888 ideal for portable sound reinforcement system applications. The rated bandwidth of 2kHz to beyond 15kHz make this system ideal for two way system designs.

P.Audio BM-D442

BM-D442 The P Audio BM-D442 is a 1.75 inch (44.4mm) medium format diaphragm compression driver coupled to a high density magnetic circuit. The compression driver exit diameter is an industry standard 1 inch (25.4mm). The design of the 442 is based on the extremely successful BM-D440 technology and represents substantial technological advances in both sound quality and ease of integration into system designs. The BM-D442 combines high magnetic field strength and a very lightweight diaphragm assembly, producing in a very high output device that also features extended bandwidth and well defined frequency response. The phase plug is a circumferential slot design that has been redesigned to provide both extended bandwidth and superior response linearity. The phase plug to diaphragm spacing has been optimized for both extended frequency response and increased acoustic damping. The BM-D442 is optimized for very high performance two way system designs and is an excellent high frequency device for professional two way systems. BM-D442 The P Audio BM-D442 is a 1.75 inch (44.4mm) medium format diaphragm compression driver coupled to a high density magnetic circuit. The compression driver exit diameter is an industry standard 1 inch (25.4mm). The design of the 442 is based on the extremely successful BM-D440 technology and represents substantial technological advances in both sound quality and ease of integration into system designs. The BM-D442 combines high magnetic field strength and a very lightweight diaphragm assembly, producing in a very high output device that also features extended bandwidth and well defined frequency response. The phase plug is a circumferential slot design that has been redesigned to provide both extended bandwidth and superior response linearity. The phase plug to diaphragm spacing has been optimized for both extended frequency response and increased acoustic damping. The BM-D442 is optimized for very high performance two way system designs and is an excellent high frequency device for professional two way systems.

P.Audio BM-D460 / BM-D460S

The P.Audio has redefined its BM series of compression drivers. The BMD460S is a state of the art high output compression driver. New developments P.Audio Research and Development have produced new levels of performance. State of the art manufacturing methods insure extremely reliable and consistent designs. The new BM-D460S driver utilizes the recently developed CRT™ technology to substantially improve both the time domain response and reduce distortion through the critical upper vocal range (1.5kHz to 5kHz). This new technology, called Cavity Resonance Technology ™ (CRT) acts to acoustically minimize the cavity found under all suspension driver suspension elements. By employing CRT technology, P.Audio engineers have been able to greatly improve the vocal accuracy in the frequency range where vocal intelligibility is located. Magnetic fluid has also been added to increase thermal transfer and mechanical damping. These changes to the diaphragm and magnet structure assembly have also increased the sound pressure levels and smoothed the response between 10kHz and 20kHz. The result is a more accurate system, particularly for vocal range program material. The BM-D460S is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry, high temperature aluminum to insure extended high frequency response. This diaphragm geometry is ideally suited for foreground/background high performance pa systems. The 1.0 inch (25.4mm) throat exit makes the 460S an excellent choice for extended bandwidth and ultra high frequency applications such as three way designs. The BM-D460S is ideally suited for line array applications or other applications where a mid bass horn or direct radiator driver is also used. This medium format throat and medium format diaphragm insures wide dispersion at very high frequencies and is an excellent choice for three way systems or medium power two way designs. The 1.0 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.0 inch screw/thread on horns. The Ferrite based permanent magnetic system produces a very high efficiency and value. This makes the BM-D460S ideal for professional applications as well as fixed installation systems. The large format Ferrite permanent magnet produces a very high conversion efficiency. The P.Audio has redefined its BM series of compression drivers. The BMD460S is a state of the art high output compression driver. New developments P.Audio Research and Development have produced new levels of performance. State of the art manufacturing methods insure extremely reliable and consistent designs. The new BM-D460S driver utilizes the recently developed CRT™ technology to substantially improve both the time domain response and reduce distortion through the critical upper vocal range (1.5kHz to 5kHz). This new technology, called Cavity Resonance Technology ™ (CRT) acts to acoustically minimize the cavity found under all suspension driver suspension elements. By employing CRT technology, P.Audio engineers have been able to greatly improve the vocal accuracy in the frequency range where vocal intelligibility is located. Magnetic fluid has also been added to increase thermal transfer and mechanical damping. These changes to the diaphragm and magnet structure assembly have also increased the sound pressure levels and smoothed the response between 10kHz and 20kHz. The result is a more accurate system, particularly for vocal range program material. The BM-D460S is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry, high temperature aluminum to insure extended high frequency response. This diaphragm geometry is ideally suited for foreground/background high performance pa systems. The 1.0 inch (25.4mm) throat exit makes the 460S an excellent choice for extended bandwidth and ultra high frequency applications such as three way designs. The BM-D460S is ideally suited for line array applications or other applications where a mid bass horn or direct radiator driver is also used. This medium format throat and medium format diaphragm insures wide dispersion at very high frequencies and is an excellent choice for three way systems or medium power two way designs. The 1.0 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.0 inch screw/thread on horns. The Ferrite based permanent magnetic system produces a very high efficiency and value. This makes the BM-D460S ideal for professional applications as well as fixed installation systems. The large format Ferrite permanent magnet produces a very high conversion efficiency.

P.Audio PA-D26S

The P.Audio PA-D26S is a small format diaphragm compression driver designed for mid range and extended high frequency applications in two way professional sound reinforcement systems. The small format design is excellent for wide bandwidth applications and is ideal for medium sized sound reinforcement systems using 8 inch (203mm) and 10 inch (254mm) woofers. The driver has a rated bandwidth of 1.5kHz to beyond 20kHz. The PA-D26S is a Ferrite based permanent magnet system that features a 1 inch (25.4mm) diameter phenolic resin impregnated diaphragm assembly. This design features P.Audio"s legendary high temperature systems to insure both high power handling and high reliability. The PA-D26S features an industry standard screw on style exit that allows the driver to easily mate to any high frequency horn with a standard 1 inch screw on mounting. The P.Audio PA-D26S is a small format diaphragm compression driver designed for mid range and extended high frequency applications in two way professional sound reinforcement systems. The small format design is excellent for wide bandwidth applications and is ideal for medium sized sound reinforcement systems using 8 inch (203mm) and 10 inch (254mm) woofers. The driver has a rated bandwidth of 1.5kHz to beyond 20kHz. The PA-D26S is a Ferrite based permanent magnet system that features a 1 inch (25.4mm) diameter phenolic resin impregnated diaphragm assembly. This design features P.Audio"s legendary high temperature systems to insure both high power handling and high reliability. The PA-D26S features an industry standard screw on style exit that allows the driver to easily mate to any high frequency horn with a standard 1 inch screw on mounting.

P.Audio PreNeo-340S

The P Audio PreNeo-340S is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-340S is a small format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. This diaphragm geometry is ideally suited for foreground/background high performance pa systems. The P Audio PreNeo-340S is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-340S is a small format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response.

P.Audio PreNeo-450N

The P Audio PreNeo-450N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-450N is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The P Audio PreNeo-450N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-450N is a medium format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response.

P.Audio SD-44BN

The P.Audio SD-44BN is a medium format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-44BN has an operating range of 1200Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-44BN is a neodymium based magnetic system with an industry standard 1 inch (25.4mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-44BN. The uses of neodymium magnetics allows the SD-44BN to be used in "close spaced" array designs such as modern high output line arrays. The diaphragm assembly is a 1.75 inch (44.4mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 50 watts of power handling capacity. The larger diaphragm diameter (1.75 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems. The P.Audio SD-44BN is a medium format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-44BN has an operating range of 1200Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-44BN is a neodymium based magnetic system with an industry standard 1 inch (25.4mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-44BN. The uses of neodymium magnetics allows the SD-44BN to be used in "close spaced" array designs such as modern high output line arrays. The diaphragm assembly is a 1.75 inch (44.4mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 50 watts of power handling capacity. The larger diaphragm diameter (1.75 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems.

P.Audio BM-D740

The P.Audio BM-D740 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D740 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 1.4 inch (35.5mm) throat exit makes the 740 an excellent choice for extended bandwidth and high sound pressure level performance.This medium format throat insures low distortion and high intelligibility and is an industry standard for professional audio applications. This throat diameter has become an industry reference when combined low distortion and extended bandwidth are required. The 1.4 inch diameter throat insures wide dispersion at high frequencies. The 1.4 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.4 inch bolt on horns. The Ferrite based permanent magnetic system produces a very high efficiency.This makes the BM-D740 ideal for high level professional touring applications as well as high level fixed installation systems. The large Ferrite permanent magnet produces remarkably high conversion efficiency. The P.Audio BM-D740 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D740 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 1.4 inch (35.5mm) throat exit makes the 740 an excellent choice for extended bandwidth and high sound pressure level performance.This medium format throat insures low distortion and high intelligibility and is an industry standard for professional audio applications. This throat diameter has become an industry reference when combined low distortion and extended bandwidth are required. The 1.4 inch diameter throat insures wide dispersion at high frequencies. The 1.4 inch throat is compatible with a variety of P.Audio horns and also compatible with industry standard 1.4 inch bolt on horns. The Ferrite based permanent magnetic system produces a very high efficiency.This makes the BM-D740 ideal for high level professional touring applications as well as high level fixed installation systems. The large Ferrite permanent magnet produces remarkably high conversion efficiency.

P.Audio PreNeo-740N

The P Audio PreNeo-740N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-740N is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The P Audio PreNeo-750N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-750N is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response.

P.Audio SD-63BN

The P.Audio SD-63BN is a ultra medium format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-63BN has an operating range of 1000Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-63BN is a neodymium based magnetic system with an industry standard 1.4 inch (35.5mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-63BN. The use of neodymium allows the SD-63N to be used in close spaced designs such as modern line array systems. The diaphragm assembly is a 2.5 inch (63.5mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 80 watts of power handling capacity. The larger diaphragm diameter (2.5 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems. The P.Audio SD-63BN is a ultra medium format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-63BN has an operating range of 1000Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-63BN is a neodymium based magnetic system with an industry standard 1.4 inch (35.5mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-63BN. The use of neodymium allows the SD-63N to be used in close spaced designs such as modern line array systems. The diaphragm assembly is a 2.5 inch (63.5mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 80 watts of power handling capacity. The larger diaphragm diameter (2.5 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems.

P.Audio SD-75BN

The P.Audio SD-75BN is a large format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-75BN has an operating range of 800Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-75BN is a neodymium based magnetic system with an industry standard 1.4 inch (35.5mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-75BN. The neodymium design allows the driver to be used in modern line array designs where close spacing is required. The diaphragm assembly is a 3 inch (76.2mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 100 watts of power handling capacity. The larger diaphragm diameter (3 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems. The P.Audio SD-75BN is a large format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The SD-75BN has an operating range of 800Hz to 20000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement systems. The SD-75BN is a neodymium based magnetic system with an industry standard 1.4 inch (35.5mm) exit diameter. The mounting configuration is a standard "bolt on" style. P.Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the SD-75BN. The neodymium design allows the driver to be used in modern line array designs where close spacing is required. The diaphragm assembly is a 3 inch (76.2mm) diameter commercially pure titanium design and utilizes P.Audio"s very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 100 watts of power handling capacity. The larger diaphragm diameter (3 inch) provides superior mid band response and is an excellent choice for medium power professional sound reinforcement systems.

P.Audio BM-D750(II)

The P Audio BM-D750(II) is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D750(II) is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 750 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D750(II) ideal for high level professional touring applications as well as high level fixed installation systems. The P Audio BM-D750(II) is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D750(II) is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 750 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D750(II) ideal for high level professional touring applications as well as high level fixed installation systems.

P.Audio BM-D760

The P.Audio BM-D760 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D760 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 760 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P.Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D760 ideal for high level professional touring applications as well as high level fixed installation systems. The P.Audio BM-D760 is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The BM-D760 is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The large 2 inch (51mm) throat exit makes the 760 an excellent choice for high sound pressure level performance. This large throat insures low distortion and high intelligibility, particularly thru the critical upper vocal range. High fidelity thru the upper vocal range translates to increased intelligibility and clarity in this critical upper vocal range. This throat diameter is an industry standard for high output vocal range compression drivers and will mate to a variety of P.Audio 2 inch throat horns as well as many commercially available high frequency horns. The Ferrite based permanent magnetic system produces a very high efficiency to weight and size ratio. This makes the BM-D760 ideal for high level professional touring applications as well as high level fixed installation systems.

P.audio BM-D950

The P.Audio BM-D950 is a very high performance ultra large format compression driver. The driver features a large optimized ferrite motor that provides extended high frequency response and bandwidth. The ultra large format 4 inch (101.6mm) titanium diaphragm produces very high sound pressure level performance. The BM-D950 offers superior vocal fundamentals and excellent vocal range intelligibility while also offering extended high frequency response. The increased magnetic volume insures elevated thermal reliability and reduced high frequency power compression as well as extended high frequency content. The BM-D950 offers very high continuous power handling and excellent reliability. The design allows for the driver to be crossed over as low as 800Hz yet still exhibits full specification performance. The rated continuous power handling is 150 watts. The BM-D950 features a finite element optimized ferrite magnet structure that offers excellent magnetic efficiency. The design features an industry standard 2.0 inch (50.8mm) exit diameter that will accommodate most standard bolt on style high frequency horns. Useable frequency range is 800Hz to 18kHz. The amplitude response is very controlled and offers excellent time domain response. The P.Audio BM-D950 is a very high performance ultra large format compression driver. The driver features a large optimized ferrite motor that provides extended high frequency response and bandwidth. The ultra large format 4 inch (101.6mm) titanium diaphragm produces very high sound pressure level performance. The BM-D950 offers superior vocal fundamentals and excellent vocal range intelligibility while also offering extended high frequency response. The increased magnetic volume insures elevated thermal reliability and reduced high frequency power compression as well as extended high frequency content. The BM-D950 offers very high continuous power handling and excellent reliability. The design allows for the driver to be crossed over as low as 800Hz yet still exhibits full specification performance. The rated continuous power handling is 150 watts. The BM-D950 features a finite element optimized ferrite magnet structure that offers excellent magnetic efficiency. The design features an industry standard 2.0 inch (50.8mm) exit diameter that will accommodate most standard bolt on style high frequency horns. Useable frequency range is 800Hz to 18kHz. The amplitude response is very controlled and offers excellent time domain response.

P.Audio PA-D99

The P Audio PA-D99 is a large format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The PA-D99 has an operating range of 500Hz to 18000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement system. The PA-D99 is a ferrite based magnetic system with an industry standard 2 inch exit diameter. The mounting configuration is a standard "bolt on" style. P Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the PA-D99. The diaphragm assembly is a 4 inch diameter commercially pure titanium design and utilizes P Audio's P Audio's very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 150 watts of power handling capacity. The larger diaphragm diameter (4 inch) medium power professional sound reinforcement systems. The P Audio PA-D99 is a large format compression driver that utilizes a precision formed diaphragm assembly. The titanium diaphragm is precision formed to insure excellent consistency and performance. The diaphragm assembly is close spaced to a precision phase plug to insure excellent acoustic loading. The PA-D99 has an operating range of 500Hz to 18000Hz and is ideally suited for two way and three way high frequency applications in professional sound reinforcement system. The PA-D99 is a ferrite based magnetic system with an industry standard 2 inch exit diameter. The mounting configuration is a standard "bolt on" style. P Audio offers a wide variety high frequency horns that will provide excellent pattern control and acoustic loading for the PA-D99. The diaphragm assembly is a 4 inch diameter commercially pure titanium design and utilizes P Audio's P Audio's very high temperature adhesive systems and precision manufacturing to insure high power handling and reliability. The construction yields a full 150 watts of power handling capacity. The larger diaphragm diameter (4 inch) medium power professional sound reinforcement systems.

P.Audio PreNeo-750N

The P Audio PreNeo-750N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-750N is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response. The P Audio PreNeo-750N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The PreNeo-750N is a large format titanium based diaphragm assembly mated to a close spaced circumferential phase plug geometry. The voice coil is a rectangular geometry high temperature aluminum to insure extended high frequency response.

P.Audio SD-750N

The P Audio SD-750N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity. The P Audio SD-750N is a state of the art high output compression driver. Advanced engineering and manufacturing methods have produced an extremely reliable and wide bandwidth device that also features very high fidelity.